MC9S08GT8ACFBE Freescale Semiconductor, MC9S08GT8ACFBE Datasheet - Page 91

• Manufacturer Part Number: MC9S08GT8ACFBE
• Description: IC MCU 8K FLASH 1K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT8ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6.5.3
Port C includes eight general-purpose I/O pins that share with the SCI2 and IIC modules. Port C pins used
as general-purpose I/O pins are controlled by the port C data (PTCD), data direction (PTCDD), pullup
enable (PTCPE), and slew rate control (PTCSE) registers.
If the SCI2 takes control of a port C pin, the corresponding PTCDD bit is ignored. PTCSE can be used to
provide slew rate on the SCI2 transmit pin, TxD2. PTCPE can be used, provided the corresponding
PTCDD bit is 0, to provide a pullup device on the SCI2 receive pin, RxD2.
If the IIC takes control of a port C pin, the corresponding PTCDD bit is ignored. PTCSE can be used to
provide slew rate on the IIC serial data pin (SDA), when in output mode and the IIC clock pin (SCL).
PTCPE can be used, provided the corresponding PTCDD bit is 0, to provide a pullup device on the IIC
serial data pin, when in receive mode.
Reads of PTCD will return the logic value of the corresponding pin, provided PTCDD is 0.
Freescale Semiconductor
PTCD[7:0]
Reset
Field
7:0
W
R
PTCD7
Port C Registers (PTCD, PTCPE, PTCSE, and PTCDD)
Port C Data Register Bits— For port C pins that are inputs, reads return the logic level on the pin. For port C
pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port C pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTCD to all 0s, but these 0s are not driven out the corresponding pins because reset also
configures all port pins as high-impedance inputs with pullups disabled.
0
7
PTCD6
0
6
Figure 6-16. Port C Data Register (PTCD)
MC9S08GT16A/GT8A Data Sheet, Rev. 1
PTCD5
Table 6-9. PTCD Field Descriptions
0
5
PTCD4
0
4
Description
PTCD3
3
0
PTCD2
0
2
PTCD1
0
1
Parallel Input/Output
PTCD0
0
0
91