MC9S08GB60ACFUE Freescale Semiconductor, MC9S08GB60ACFUE Datasheet - Page 178

• Manufacturer Part Number: MC9S08GB60ACFUE
• Description: IC MCU 60K FLASH 4K RAM 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GB60ACFUE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08GB
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 8
• Operating Supply Voltage: 0 V to 1.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Serial Communications Interface (S08SCIV1)
11.2.3
This register can be read or written at any time.
178
Reset
Field
TCIE
ILIE
TIE
RIE
RE
TE
7
6
5
4
3
2
W
R
SCI Control Register 2 (SCIxC2)
TIE
Transmit Interrupt Enable (for TDRE)
0 Hardware interrupts from TDRE disabled (use polling).
1 Hardware interrupt requested when TDRE flag is 1.
Transmission Complete Interrupt Enable (for TC)
0 Hardware interrupts from TC disabled (use polling).
1 Hardware interrupt requested when TC flag is 1.
Receiver Interrupt Enable (for RDRF)
0 Hardware interrupts from RDRF disabled (use polling).
1 Hardware interrupt requested when RDRF flag is 1.
Idle Line Interrupt Enable (for IDLE)
0 Hardware interrupts from IDLE disabled (use polling).
1 Hardware interrupt requested when IDLE flag is 1.
Transmitter Enable
0 Transmitter off.
1 Transmitter on.
TE must be 1 in order to use the SCI transmitter. When TE = 1, the SCI forces the TxD pin to act as an output
for the SCI system.
When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of
traffic on the single SCI communication line (TxD pin).
TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress.
Refer to
When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued
break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin.
Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin. If
LOOPS = 1 , the RxD pin reverts to being a general-purpose I/O pin even if RE = 1.
0 Receiver off.
1 Receiver on.
0
7
Section 11.3.2.1, “Send Break and Queued
TCIE
0
6
Table 11-4. SCIxC2 Register Field Descriptions
Figure 11-7. SCI Control Register 2 (SCIxC2)
RIE
MC9S08GB60A Data Sheet, Rev. 2
0
5
ILIE
0
4
Description
Idle,” for more details.
TE
3
0
RE
0
2
Freescale Semiconductor
RWU
0
1
SBK
0
0