C8051F063-GQR Silicon Laboratories Inc, C8051F063-GQR Datasheet - Page 161

• Manufacturer Part Number: C8051F063-GQR
• Description: IC 8051 MCU 64K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F063-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN, I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F060DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit, 1 Channel
• On-chip Dac: 12 bit, 2 Channel
• For Use With: 336-1214 - DEV KIT FOR F060/F062/F063
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

13.4.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes. In Stop mode, the CPU and internal oscillators are stopped, effectively
shutting down all digital peripherals. Each analog peripheral must be shut down individually prior to enter-
ing Stop Mode. Stop mode can only be terminated by an internal or external reset. On reset, the CIP-51
performs the normal reset sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to sleep for longer than the MCD
timeout of 100 µs.
Bits7-2:
Bit1:
Bit0:
R/W
Bit7
-
Reserved.
STOP: STOP Mode Select.
Writing a ‘1’ to this bit will place the CIP-51 into STOP mode. This bit will always read ‘0’.
1: CIP-51 forced into power-down mode. (Turns off internal oscillator).
IDLE: IDLE Mode Select.
Writing a ‘1’ to this bit will place the CIP-51 into IDLE mode. This bit will always read ‘0’.
1: CIP-51 forced into IDLE mode. (Shuts off clock to CPU, but clock to Timers, Interrupts,
and all peripherals remain active.)
See Note in Section
R/W
Bit6
-
R/W
Bit5
-
“13.4.1. Idle
Figure 13.25. PCON: Power Control
R/W
Bit4
-
Mode” on page 160.
Rev. 1.2
R/W
Bit3
-
C8051F060/1/2/3/4/5/6/7
R/W
Bit2
-
STOP
R/W
Bit1
SFR Address:
SFR Page:
IDLE
R/W
Bit0
0x87
All Pages
Reset Value
00000000
161