HD64F3048F16 Renesas Electronics America, HD64F3048F16 Datasheet - Page 576

• Manufacturer Part Number: HD64F3048F16
• Description: IC H8 MCU FLASH 128K 100QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Hr

Specifications of HD64F3048F16

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 70
• Interface Type: SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 15 A/D Converter
15.5
The A/D converter generates an interrupt (ADI) at the end of A/D conversion. The ADI interrupt
request can be enabled or disabled by the ADIE bit in ADCSR.
15.6
When using the A/D converter, note the following points:
1. Analog Input Voltage Range: During A/D conversion, the voltages input to the analog input
2. Relationships of AV
3. V
4. Analog Voltage: When using an A/D converter, make the following voltage settings.
5. Note on Board Design: In board layout, separate the digital circuits from the analog circuits as
Rev. 7.00 Sep 21, 2005 page 550 of 878
REJ09B0259-0700
pins should be in the range AV
as follows: AV
used.
V
a. V
b. AV
Note: Restriction for the ZTAT version only; The S-mask version of ZTAT, the Flash
Failure to observe points 1, 2, 3, and 4 above may degrade chip reliability.
much as possible. Particularly avoid layouts in which the signal lines of digital circuits cross or
closely approach the signal lines of analog circuits. Induction and other effects may cause the
analog circuits to operate incorrectly, or may adversely affect the accuracy of A/D conversion.
The analog input signals (AN
voltage (AV
analog ground (AV
board.
REF
REF
(N = 0 to 7)
Programming Range: The reference voltage input at the V
CC
Interrupts
Usage Notes
CC
AV
Memory version and Mask ROM version can be used regularly without restriction.
AV
CC
V
CC
.
CC
REF
) must be separated from digital circuits by the analog ground (AV
SS
– 0.3V
= V
ANn
SS
CC
) should be connected to a stable digital ground (V
SS
. AV
and AV
AV
CC
0
SS
and AV
SS
to AN
SS
= V
to V
AN
SS
7
CC
), analog reference voltage (V
SS
n
and V
must not be left open, even if the A/D converter is not
V
REF
SS
.
: AV
CC
, AV
SS
, V
REF
CC
pin should be in the range
, and V
REF
), and analog supply
SS
) at one point on the
SS
should be related
SS
). The