M37632EFFP#U2 Renesas Electronics America, M37632EFFP#U2 Datasheet - Page 114
M37632EFFP#U2
Manufacturer Part Number
M37632EFFP#U2
Description
IC 740 MCU 80QFP
Manufacturer
Renesas Electronics America
Datasheet
1.M37632EFFPU2.pdf
(195 pages)
Specifications of M37632EFFP#U2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 114 of 195
- Download datasheet (2Mb)
NOTES ON USE
4.2 Termination of unused pins
At the termination of unused pins, perform wiring at the shortest possible distance (20 mm
or less) from microcomputer pins. With regard to an effects on the system, thoroughly perform
system evaluation on the user side.
Rev.2.00 Nov 14, 2006
REJ09B0322-0200
4.2.1 Appropriate termination of unused pins
4.2.2 Termination remarks
Reason
Reason
Reason
Open.
Connect each pin via a 1 kΩ to 10 kΩ resistor (reference value) to V
allows selection of an on-chip pull-up or pull-down resistor, the on-chip pull-up or pull-
down resistor may be used.
In addition, pins (CNV
the voltage level, select V
Set the I/O ports for the input mode and connect them to V
of 1 kΩ to 10 kΩ (reference value).
Ports that permit the selecting of a built-in pull-up/pull-down resistor can also use this
resistor. Set the I/O ports for the output mode and open them at “L” or “H”.
• When opening them in the output mode, the input mode of the initial status remains until
• Since the direction register setup may be changed because of a program runaway or
When not using the A/D converter, handle a power source pin for the A/D converter, AV
and AV
• AV
• AV
Do not open in the input mode.
• The power source current may increase depending on the first-stage circuit.
• An effect due to noise may be easily produced as compared with proper termination
When setting for the input mode, do not connect to V
If the direction register setup changes for the output mode because of a program runaway
or noise, a short circuit may occur between a port and V
When setting for the input mode, do not connect multiple ports in a lump to V
through a resistor.
If the direction register setup changes for the output mode because of a program runaway
or noise, a short circuit may occur between ports.
Output-only pins:
Input-only pins:
I/O ports:
The AVss pin when not using the A/D converter:
I/O ports:
I/O ports:
I/O ports:
the mode of the ports is switched over to the output mode by the program after reset.
Thus, the potential at these pins is undefined and the power source current may increase
in the input mode. With regard to an effects on the system, thoroughly perform system
evaluation on the user side.
noise, set direction registers by program periodically to increase the reliability of program.
and shown on the above.
SS
CC
: Connect to the V
: Connect to the V
CC
pins as follows:
page 106 of 185
SS
and INT pins, etc.) for which the operating mode is affected by
SS
CC
CC
pin.
pin.
or V
SS
after checking the mode.
CC
or V
CC
CC
or V
(or V
SS
directly.
SS
SS
through each resistor
).
CC
or V
SS
. If the port
CC
or V
SS
SS
Related parts for M37632EFFP#U2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: