AT90S4433-8PI Atmel, AT90S4433-8PI Datasheet - Page 85
![IC MCU 4K FLSH 8MHZ A/D IT 28DIP](/photos/7/21/72189/453-28-dip_sml.jpg)
AT90S4433-8PI
Manufacturer Part Number
AT90S4433-8PI
Description
IC MCU 4K FLSH 8MHZ A/D IT 28DIP
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheet
1.AT90S4433-8AC.pdf
(126 pages)
Specifications of AT90S4433-8PI
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
4KB (2K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 6x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT90S4433-8PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Memory
Programming
Program and Data
Memory Lock Bits
Fuse Bits
Signature Bytes
1042H–AVR–04/03
The AT90S4433 MCU provides two Lock bits, which can be left unprogrammed (“1”) or
can be programmed (“0”) to obtain the additional features listed in Table 28. The Lock
bits can only be erased with the Chip Erase command.
Table 28. Lock Bit Protection Modes
Note:
The AT90S4433 has six Fuse bits, SPIEN, BODLEVEL, BODEN and CKSEL2..0.
•
•
•
•
All Atmel microcontrollers have a 3-byte signature code that identifies the device. This
code can be read in both serial and parallel mode. The three bytes reside in a separate
address space.
For the AT90S4433
Note:
Mode
Memory Lock Bits
1
2
3
When the SPIEN Fuse is programmed (“0”), Serial Program and Data Downloading
is enabled. Default value is programmed (“0”). This bit is not accessible in Serial
Programming mode.
The BODLEVEL Fuse selects the Brown-out Detection Level and changes the start-
up times. See “Brown-out Detection” on page 25. Default value is unprogrammed
(“1”).
When the BODEN Fuse is programmed (“0”), the Brown-out Detector is enabled.
See “Brown-out Detection” on page 25. Default value is unprogrammed (“1”).
CKSEL2..0: See Table 5 on page 23 for which combination of CKSEL2..0 to use.
Default value is “010”.
1. $000: $1E (indicates manufactured by Atmel)
2. $001: $92 (indicates 4 KB Flash memory)
3. $002: $03 (indicates AT90S4433 device when signature byte $001 is $92)
1. In Parallel mode, programming of the Fuse bits are also disabled. Program the Fuse
1. When both Lock bits are programmed (Lock mode 3), the signature bytes cannot be
LB1
bits before programming the Lock bits.
read in Serial mode. Reading the signature bytes will return $00, $01 and $02.
1
0
0
LB2
1
1
0
(1)
they are:
Protection Type
No memory lock features enabled.
Further programming of the Flash and EEPROM is disabled.
Same as mode 2, and verify is also disabled.
AT90S/LS4433
(1)
85