AT91SAM7S128C-AU Atmel, AT91SAM7S128C-AU Datasheet - Page 528

• Manufacturer Part Number: AT91SAM7S128C-AU
• Description: IC ARM7 MCU 32BIT 128K 64LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S128C-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: AT91SAM7S128-AU-001; AT91SAM7S128AU001; AT91SAM7S128AU001

• RX_DATA_BK0: Receive Data Bank 0
This flag generates an interrupt while it is set to one.
Write (Cleared by the firmware):
0 = Notify USB peripheral device that data have been read in the FIFO's Bank 0.
1 = To leave the read value unchanged.
Read (Set by the USB peripheral):
0 = No data packet has been received in the FIFO's Bank 0.
1 = A data packet has been received, it has been stored in the FIFO's Bank 0.
When the device firmware has polled this bit or has been interrupted by this signal, it must transfer data from the FIFO to
the microcontroller memory. The number of bytes received is available in RXBYTCENT field. Bank 0 FIFO values are read
through the UDP_ FDRx register. Once a transfer is done, the device firmware must release Bank 0 to the USB peripheral
device by clearing RX_DATA_BK0.
After setting or clearing this bit, a wait time of 3 UDPCK clock cycles and 3 peripheral clock cycles is required before
accessing DPR.
• RXSETUP: Received Setup
This flag generates an interrupt while it is set to one.
Read:
0 = No setup packet available.
1 = A setup data packet has been sent by the host and is available in the FIFO.
Write:
0 = Device firmware notifies the USB peripheral device that it has read the setup data in the FIFO.
1 = No effect.
This flag is used to notify the USB device firmware that a valid Setup data packet has been sent by the host and success-
fully received by the USB device. The USB device firmware may transfer Setup data from the FIFO by reading the UDP_
FDRx register to the microcontroller memory. Once a transfer has been done, RXSETUP must be cleared by the device
firmware.
Ensuing Data OUT transaction is not accepted while RXSETUP is set.
• STALLSENT: Stall Sent (Control, Bulk Interrupt Endpoints)/ISOERROR (Isochronous Endpoints)
This flag generates an interrupt while it is set to one.
STALLSENT: This ends a STALL handshake.
Read:
0 = The host has not acknowledged a STALL.
1 = Host has acknowledged the stall.
Write:
0 = Resets the STALLSENT flag, clears the interrupt.
1 = No effect.
AT91SAM7S Series Preliminary
528
6175K–ATARM–30-Aug-10