ST16C550CQ48-F Exar Corporation, ST16C550CQ48-F Datasheet - Page 17

• Manufacturer Part Number: ST16C550CQ48-F
• Description: IC UART FIFO 16B SGL 48TQFP
• Manufacturer: Exar Corporation
• Type: UART with 16-byte FIFOsr

Specifications of ST16C550CQ48-F

• Number Of Channels: 1, UART
• Package / Case: 48-TQFP
• Features: *
• Fifo's: 16 Byte
• Voltage - Supply: 2.97 V ~ 5.5 V
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 1.5 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.97 V
• Supply Current: 3 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V, 5 V
• No. Of Channels: 1
• Supply Voltage Range: 2.97V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 48
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1260

ISR BIT-0:
Logic 0 = An interrupt is pending and the ISR contents
may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending. (normal default condi-
tion)
ISR BIT 1-3: (logic 0 or cleared is the default condition)
These bits indicate the source for a pending interrupt at
interrupt priority levels 1, 2, and 3 (See Interrupt Source
Table).
ISR BIT 4-5: Not used and set to “0”.
ISR BIT 6-7: (logic 0 or cleared is the default condition)
These bits are set to a logic 0 when the FIFO is not being
used. They are set to a logic 1 when the FIFO’s are
enabled
Line Control Register (LCR)
The Line Control Register is used to specify the
asynchronous data communication format. The word
length, the number of stop bits, and the parity are
selected by writing the appropriate bits in this register.
LCR BIT 0-1: (logic 0 or cleared is the default condi-
tion)
These two bits specify the word length to be transmit-
ted or received.
LCR BIT-2: (logic 0 or cleared is the default condition)
The length of stop bit is specified by this bit in
conjunction with the programmed word length.
BIT-1
Rev. 5.01
0
0
1
1
BIT-0
0
1
0
1
Word length
5
6
7
8
17
LCR BIT-3:
Parity or no parity can be selected via this bit.
Logic 0 = No parity (normal default condition)
Logic 1 = A parity bit is generated during the transmis-
sion, receiver checks the data and parity for transmis-
sion errors.
LCR BIT-4:
If the parity bit is enabled with LCR bit-3 set to a logic
1, LCR BIT-4 selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd
number of logic 1’s in the transmitted data. The
receiver must be programmed to check the same
format. (normal default condition)
Logic 1 = EVEN Parity is generated by forcing an even
the number of logic 1’s in the transmitted. The receiver
must be programmed to check the same format.
LCR BIT-5:
If the parity bit is enabled, LCR BIT-5 selects the
forced parity format.
LCR BIT-5 = logic 0, parity is not forced (normal
default condition)
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit
is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit
is forced to a logical 0 for the transmit and receive
data.
Bit-5
LCR
BIT-2
X
0
0
1
1
0
1
1
Bit-4
LCR
Word length
X
0
1
0
1
5,6,7,8
6,7,8
5
Bit-3
LCR
0
1
1
1
1
ST16C550
Parity selection
No parity
Odd parity
Even parity
Force parity “1”
Forced “0”
(Bit time(s))
Stop bit
length
1-1/2
1
2