MTCMR-G-F4 Multi-Tech Systems, MTCMR-G-F4 Datasheet - Page 109

• Manufacturer Part Number: MTCMR-G-F4
• Description: MODEM GPRS QUAD BAND GSM GLOBAL
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® iCellr

Specifications of MTCMR-G-F4

• Frequency: 850MHz, 900MHz, 1.8GHz, 1.9GHz
• Applications: General Purpose
• Interface: RS-232, USB
• Function: Transceiver, Modem
• Data Rate - Maximum: 115.2kbps
• Modulation Or Protocol: GSM, GPRS
• Voltage - Supply: 9 V ~ 32 V
• Package / Case: Module with Case
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Power - Output: -
• Sensitivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 881-1151; MTCMR-G-F4

General Indications +WIND
Multi-Tech Systems, Inc. GPRS AT Commands Reference Guide (Document Number S000293J)
Description:
Values:
This command provides a general mechanism to send unsolicited non-standardized indications to the
application. The indicators are:
For each of these indications, a “bit flow” has to be indicated.
<IndLevel>
<event>
•
•
•
•
10
11
12
13
Indication of a physical change on the SIM detect pin from the connector (meaning SIM inserted,
Indication during mobile originated call setup that the calling party is ringing.
Indication of the availability of the product to receive AT commands after boot.
NITZ indication (Network Information and Time Zone)
0
1 (bit-0)
2 (bit-1)
4 (bit-2)
8 (bit-3)
16 (bit-4)
32 (bit-5)
64 (bit-6)
128 (bit-7)
256 (bit-8)
512 (bit-9)
1024 (bit-10)
2048 (bit-11)
4096 (bit-12)
8192 (bit-13)
16384 (bit-14)
Combination (addition of the values) is used to allow more than one indication flow: 0 ≤ IndLevel ≤
32767
0
1
2
3
4
5
6
7:
8
9
SIM removed)
•
The SIM presence pin has been detected as “SIM removed”
The SIM presence pin has been detected as “SIM inserted”
Calling party is alerting
Product is ready to process AT commands (except phonebooks, AOC, SMS), at init or after
AT+CFUN=1
Product is ready to process all AT commands, end of phonebook init or swap (FDN to ADN)
Call <idx> has been created (after ATD or +CCWA…)
Call <idx> has been released, after a NO CARRIER, a +CSSU: 5 indication, or after the
release of a call waiting.
The network service is available for an emergency call.
The network is lost.
Audio ON.
Show reload status of each SIM phonebook after init phase (after Power-ON or SIM
insertion).
Show the checksum of SIM phonebooks after loading.
An interruption has occurred.
The rack has been detected as Closed.
•
To activate a specific WIND indication, <IndLevel> must have a value described above.
AT+WIND=16384 only activates SMS service indication.
To activate several WIND indications, <IndLevel> must have a value just before the last
indication required.
AT+WIND=32767 all unsolicited indications.
No unsolicited “+WIND: <IndNb>” will occur. Default.
Hardware SIM Insert/Remove indications or SIM presence after software reset.
Calling party alert indication.
Product is ready to process AT commands (except phonebooks, AOC, SMS), but
still in emergency mode.
The product is ready to process all AT commands at the end of init or after
swapping to ADN in case of FDN configuration
A new call identifier has been created (after an ATD command, +CCWA indication)
An active, held or waiting call has been released by network or other party
Network service available indication
Network lost indication
Audio ON indication
SIM phonebooks reload status
SIM phonebooks checksum indication
Interruption indication (only if FTR_INT is activated)
Hardware rack open/closed indication
NITZ indication
SMS service ready indication
Chapter 13 – Specific AT Commands
109