SPBT2532C2.AT STMicroelectronics, SPBT2532C2.AT Datasheet - Page 34
![IC BLUETOOTH VER 2.1 CLASS 2](/photos/14/20/142004/spbt2532c2_at_sml.jpg)
SPBT2532C2.AT
Manufacturer Part Number
SPBT2532C2.AT
Description
IC BLUETOOTH VER 2.1 CLASS 2
Manufacturer
STMicroelectronics
Datasheets
1.STEVAL-SPBT2ATV1.pdf
(50 pages)
2.SPBT2532C2.AT.pdf
(2 pages)
3.SPBT2532C2.AT.pdf
(55 pages)
Specifications of SPBT2532C2.AT
Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
Bluetooth v2.1+EDR, Class 2 & 3
Applications
General Purpose
Power - Output
2dBm
Sensitivity
-85dBm
Voltage - Supply
2.8 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 48kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2400 MHz to 2483.5 MHz
Interface Type
I2C, I2S, SPI, UART
Data Rate
2 Mbps
Modulation
AFH
Operating Voltage
2.8 V to 3.6 V
Antenna
Without Antenna
Board Size
10 mm x 13 mm
Operating Temperature Range
- 40 C to + 85 C
Output Power
4 mA
Security
128 bit Encryption
Technology/ Type
Class 2 Bluetooth Module
Processor Series
STLC2500
For Use With
497-10656 - BOARD DEMO BLUETOOTH SPBT2532C2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
Bluetooth Devices
Other names
497-10539
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SPBT2532C2.AT2
Manufacturer:
Broadchip
Quantity:
16 000
Command description
D.15
D.15.1
D.15.2
D.16
D.16.1
D.16.2
D.17
D.17.1
D.17.2
34/50
GPIOConfig
The GPIOConfig command is used to configure a GPIO pin to input or output.
Syntax
AT+AB GPIOConfig [GPIO Pin] [Configuration]
Where [GPIO Pin] is the Pin number, 1 – 4, of the desired GPIO to configure.
[Configuration] is i or I for input and o or O for output.
Responses
If the operation is successful, the response is:
AT-AB GPIOConfigDone
GPIORead
The GPIORead command is used to read a GPIO pin. A GPIO may be read while
configured as either an input or output.
Syntax
AT+AB GPIORead [GPIO Pin]
Where [GPIO Pin] is the Pin number, 1 – 4, of the desired GPIO to read.
Responses
If the operation is successful, the response is:
AT-AB GPIOReadDone [result]
Where [result] is either a 1 to indicate high, or 0 to indicate low.
GPIOWrite
The GPIOWrite command is used to set a GPIO pin to high or low. A GPIO may only be set
when configured as an output.
Syntax
AT+AB GPIOWrite [GPIO Pin] [Setting]
Where [GPIO Pin] is the Pin number, 1 – 4, of the desired GPIO to read. [Setting] is a
1 to set a pin to high and a 0 to set a pin to low.
Responses
If the operation is successful, the response is:
AT-AB GPIOWriteDone
Doc ID 16089 Rev 7
SPBT2532C2.AT