SPBT2532C2.AT STMicroelectronics, SPBT2532C2.AT Datasheet - Page 37

IC BLUETOOTH VER 2.1 CLASS 2

SPBT2532C2.AT

Manufacturer Part Number
SPBT2532C2.AT
Description
IC BLUETOOTH VER 2.1 CLASS 2
Manufacturer
STMicroelectronics

Specifications of SPBT2532C2.AT

Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
Bluetooth v2.1+EDR, Class 2 & 3
Applications
General Purpose
Power - Output
2dBm
Sensitivity
-85dBm
Voltage - Supply
2.8 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 48kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2400 MHz to 2483.5 MHz
Interface Type
I2C, I2S, SPI, UART
Data Rate
2 Mbps
Modulation
AFH
Operating Voltage
2.8 V to 3.6 V
Antenna
Without Antenna
Board Size
10 mm x 13 mm
Operating Temperature Range
- 40 C to + 85 C
Output Power
4 mA
Security
128 bit Encryption
Technology/ Type
Class 2 Bluetooth Module
Processor Series
STLC2500
For Use With
497-10656 - BOARD DEMO BLUETOOTH SPBT2532C2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
Bluetooth Devices
Other names
497-10539

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SPBT2532C2.AT
Manufacturer:
ST
0
Part Number:
SPBT2532C2.AT2
Manufacturer:
Broadchip
Quantity:
16 000
Part Number:
SPBT2532C2.AT2
Manufacturer:
ST
0
SPBT2532C2.AT
D.23.2
D.24
D.24.1
D.24.2
D.25
D.25.1
D.25.2
D.26
D.26.1
Responses
If the operation is successful, the response is:
AT-AB [MasterRole or SlaveRole]
SetOrigPin
The SetOrigPin command is used to set the PIN code used to originate a pairing to a
remote device.
Syntax
AT+AB SetOrigPin [PIN]
where [PIN] is the pairing code up to 16 characters (case sensitive)
Responses
There is no response for this command.
SetTermPin
The SetTermPin command is used to set the PIN code used to terminate a pairing from a
remote device.
Syntax
AT+AB SetTermPin [PIN]
where [PIN] is the pairing code up to 16 characters (case sensitive)
Responses
There is no response for this command.
SmartCableSetup
The SmartCableSetup command is used enable and configure a Smart Cable device. A
device’s BD Address is specified with which to automatically establish a connection;
replacing the need for AT connection commands. This command will override the dynamic
configuration of a Smart Cable device until the DeleteSmartCable command is issued; it is
saved in non-volatile memory.
Syntax
AT+AB SmartCableSetup [BD address] [Attempts] [Interval]
Where [BD address] is the BD address of the remote device to page and attempt to
connect. [Attempts] 0 – 999 is the number of pages that will be attempted to the specified
device until a connection is successful. A value of 0 will not automatically page the remote
device. A value of 1000 will perform unlimited pages until connected, then it will be switched
Doc ID 16089 Rev 7
Command description
37/50

Related parts for SPBT2532C2.AT