ULE-5/12-D24P-C Murata Power Solutions Inc, ULE-5/12-D24P-C Datasheet
ULE-5/12-D24P-C
Specifications of ULE-5/12-D24P-C
Related parts for ULE-5/12-D24P-C
ULE-5/12-D24P-C Summary of contents
Page 1
... OUT and sense pins (sense pins are not available on 12V or higher models). All ULE E-Bricks are certifi the BASIC- insulation requirements of UL/EN/IEC60950-1, 2nd edition, and all “D48” models (36-75V input ranges) carry the CE mark. Safety certifi cations, EMC compliance testing and qualifi ...
Page 2
... ULE-2.5/20-D24P-C 2 ULE-2.5/20-D48N-C 2 ULE-3.3/20-D12P-C 3 ULE-3.3/20-D24P-C 3 ULE-3.3/20-D48N-C 3 ULE-5/10-D12P ULE-5/12-D24P ULE-5/12-D48N ULE-12/4.2-D24P-C 12 4.2 50.4 ULE-12/4.2-D48N-C 12 4.2 50.4 ULE-24/3-D48N ULE-48/1.25-D48N-C 48 1.25 60 Please refer to the full model number structure for additional ordering part numbers and options. All specifi cations are at nominal line voltage and full load, +25ºC unless otherwise noted. ...
Page 3
... ULE BLOCK DIAGRAMS The ULE series consist of a number of unique high performance designs sharing similar mechanical outlines and pinouts. The internal architecture uses several different topologies including push-pull, fl yback and others FEEDBACK –V IN PWM CONTROLLER ON/OFF CONTROL UV, OV AND OVER-TEMPERATURE ...
Page 4
... CONTROL PWM CONTROLLER UV, OV AND OVER-TEMPERATURE COMPARATORS ULE-24/2-D48N FEEDBACK ISOLATION www.murata-ps.com ULE Series Isolated, High Density, Eighth-Brick 1.25–20 Amp, DC/DC Converters OPTO REFERENCE & ERROR AMP Typical topology is shown. email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page OUT −V OUT TRIM ...
Page 5
... The pin material is a copper alloy. The pin fi nish is suitable for both leaded and lead-free solders. Model Number ULE-1.5/20-D24P-C ULE-1.5/20-D48N-C ULE-1.8/20-D24P-C ULE-1.8/20-D48N-C ULE-2.5/20-D24P-C ULE-2.5/20-D48N-C ULE-3.3/20-D12P-C ULE-3.3/20-D24P-C ULE-3.3/20-D48N-C ULE-5/10-D12P-C ULE-5/12-D24P-C ULE-5/12-D48N-C ULE-12/4.2-D24P-C ULE-12/4.2-D48N-C ULE-24/3-D48N-C ULE-48/1.25-D48N-C www.murata-ps.com ULE Series Isolated, High Density, Eighth-Brick 1.25–20 Amp, DC/DC Converters 0.040" Pin depth* 0.25 (6.4) 0.25 (6.4) ...
Page 6
... Sense Pins omitted if function is not used 3.81 0.150 C L 3.81 0.150 ISOMETRIC VIEW THIRD ANGLE PROJECTION email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page −Input* +Input* −Output † −Sense † +Sense +Output ...
Page 7
... The Remote On/Off can be provided with either positive (P suffi negative (N suffi x) polarity. ** Sense Pins omitted if function is not used Please refer to the “ULE Connections” table. 3.81 0.150 C L 7.62 0.300 ISOMETRIC VIEW THIRD ANGLE PROJECTION email: sales@murata-ps.com 11 May 2011 MDC_ULE Series ...
Page 8
... Model Family ULE-1.5/20-D24 ULE-1.5/20-D48 ULE-1.8/20-D24 ULE-1.8/20-D48 ULE-2.5/20-D24* ULE-2.5/20-D48* ULE-3.3/20-D12* ULE-3.3/20-D24 ULE-3.3/20-D48* TYPE 'M' GULL WING SMT PACKAGE See Table ULE 'M' TYPE SMT (GULL WING) SERIES MAXIMUM HEIGHTS Model Family ULE-1.5/20-D24 M ULE-1.5/20-D48 M ULE-1.8/20-D24 M ULE-1.8/20-D48 M ULE-2.5/20-D24 M ULE-3.3/20-D12 M ULE-3.3/20-D24 M ULE-3.3/20-D48 M DIMENSIONS ARE IN INCHES [mm] TOLERANCES: 2 PLACE ...
Page 9
... Ripple/Noise Remote Sense (20 MHz Line/Load Compensation bandwidth) Regulation +10% 18 See Ordering Guide none 10% none email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page ULE Series Start-up Time Remote On/Off IN OUT regulated to V regu- OUT (Max.) lated (Max.) mSec mSec 6-90, model ...
Page 10
... Current 300mA 3.96 limiting, Continuous, hiccup output 3A 3.96 autorestart. shorted to 3A 3.96 Remove ground. overload for No damage. 5A 6.0 recovery 5A 6.0 2A 6.4 3A 15.0 3A 14.0 0.65A 28.0 500mA 55.0 email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page Relative Humidity 16 To +85ºC/85% non- condensing ...
Page 11
... Output current limit is non-latching. When the overcurrent fault is removed, the converter will immediately recover. 17. The Sense inputs are not included on lower current output models. 18. ULE-12/4.2-D24 minimum load is 0.42 Amps (10%) for rated specifi cations. 19. ULE-5/12-D24 I 20. ULE-12/4.2-D48 has no surface mount option. ...
Page 12
... Actual measured times will vary with input source impedance, external input/output capacitance, and load. The ULE Series implements a soft start circuit that limits the duty cycle of its PWM controller at power up, thereby limiting the input inrush current ...
Page 13
... If the short-circuit condition persists, another shutdown cycle will be initiated. This on/off cycling is referred to as "hiccup" mode. The hiccup cycling reduces the average output current, thereby preventing internal temperatures from rising to excessive levels. The ULE is capable of enduring an indefi nite short circuit output condition. Features and Options ...
Page 14
... Trimming Output Voltage ULE converters have a trim capability that allows users to adjust the output voltages as listed in the specifi cations. Adjustments to the output voltages can be accomplished via a trim pot (Figure single fi xed resistor as shown in Figures 7 and 8. A single fi ...
Page 15
... Use of trim and sense functions can = desired output voltage. O cause output voltages to increase thereby increasing output power beyond the ULE’s specifi ed rating or cause output voltages to climb into the output over- voltage region. Also, the use of Trim Up and Sense combined may not exceed +10 www.murata-ps.com ...
Page 16
... Surface-Mount Package ("M" suffi x) Murata Power Solutions’ ULE series SMT DC/DC converters are the only higher- power DC/DCs that can be automatically “pick-and-placed” using standard vacuum-pickup equipment and subsequently refl owed using high-temperature, lead-free solder. Virtually all SMT DC/DCs today are unprotected "open-frame" devices as- sembled by their vendors with high-temperature solder (usually Sn96.5/Ag3.5 with a melting point +221° ...
Page 17
... Orientation: When loaded into JEDEC trays, the converters are oriented in the same direction. See the diagram below. For the ULE series, a notch is placed on the top of the case (on the removal tabs) to indicate the pin 1 position. You should visually inspect the tray to be sure of this orientation. ...
Page 18
... The heat shield also includes marking for product identifi cation and a date/lot code. On ULE models, the heat shield is attached to the converter using molded plastic pins on the heat shield interior which insert into recessed dimples in the pinframe ...
Page 19
... The airfl ow collimator mixes the heat from the heating ele- ment to make uniform temperature distribution. The collimator also reduces the amount of turbulence adjacent to the UUT by restoring laminar airfl ow. Such turbulence can change the effec- tive heat transfer characteristics and give false readings. Excess turbulence removes more heat from some surfaces and less heat from others, possibly causing uneven overheating ...
Page 20
... Ambient Temperature (°C) ULE-2.5/20-D24N Maximum Current Temperature Derating V = 24V, transverse air flow at sea level IN Natural convection 100 lfm 200 lfm 300 lfm 400 lfm Ambient Temperature (°C) email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page 400 lfm ...
Page 21
... TYPICAL PERFORMANCE CURVES www.murata-ps.com ULE Series Isolated, High Density, Eighth-Brick 1.25–20 Amp, DC/DC Converters email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page ...
Page 22
... TYPICAL PERFORMANCE CURVES ULE-5/10-D12 Efficiency vs. Line Voltage and Load Current @ +25° 18V 1.2 2.4 3.6 4.8 6 7.2 Load Current (Amps 12V IN 8.4 9.6 10.8 12 www.murata-ps.com ULE Series Isolated, High Density, Eighth-Brick 1.25–20 Amp, DC/DC Converters email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page ...
Page 23
... Natural convection 100 lfm 200 lfm 300 lfm 400 lfm Ambient Temperature (°C) =48V, transverse airflow at sea level) Natural convection 100 lfm 200 lfm 300 lfm 400 lfm Ambient Temperature (°C) email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page ...
Page 24
... Amp, DC/DC Converters ULE-48/1.25-D48 Efficiency vs. Line Voltage and Load Current @ +25°C VIN = 36V VIN = 48V VIN = 60V VIN = 75V 0.22 0.33 0.45 0.56 0.68 0.79 0.91 Load Current (Amps) email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page 1.02 1.14 1.25 ...
Page 25
... TYPICAL PERFORMANCE CURVES www.murata-ps.com ULE Series Isolated, High Density, Eighth-Brick 1.25–20 Amp, DC/DC Converters email: sales@murata-ps.com 11 May 2011 MDC_ULE Series.E01 Page ...
Page 26
... ULE-48/1.25-D48 Maximum Current Temperature Derating at sea level 1.25 1.0 0.75 0.5 0.25 0 0.8 0.9 1.0 1.1 1.3 0 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi ...