D2-24044-MR-T Intersil, D2-24044-MR-T Datasheet - Page 11

• Manufacturer Part Number: D2-24044-MR-T
• Description: IC DGTL AMP AUDIO PWR D 38HTSSOP
• Manufacturer: Intersil
• Series: D2Audio™r
• Type: Class Dr

Specifications of D2-24044-MR-T

• Output Type: 2-Channel (Stereo) or 4-Channel (Quad)
• Max Output Power X Channels @ Load: 30W x 2 @ 8 Ohm
• Voltage - Supply: 9 V ~ 26 V
• Mounting Type: Surface Mount
• Package / Case: 38-TFSOP (0.173", 4.40mm Width) Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -

Input and Control Functions
PWM Inputs
Eight PWM input pins provide the PWM inputs to the
amplifier’s output stages. The PWM input pins are
electrically single-ended, referenced to the PWMVDD and
PWMGND supplies.
PWM drive to the output stages is provided differentially
on-chip, with the PWM input channels mapped to each of
the high-side output FETs and the low-side output FETs
that implement the individual power stages. Routing and
assignment of the PWM input pins to the output FETS is
defined by the configuration mode. Figures 11, 12, 13,
and 14 show the mapping of these input pins to the
outputs for each of the four configuration modes.
All eight input pins however are not always used in each
of the configuration modes. For example, in mode “00”,
providing 3-level drive of two channels of full bridge
outputs, or in mode “11” providing four independent
half-bridge outputs, one PWM input is dedicated to each
of the FETs. But in mode “01” that implements two
2-quadrant full-bridge outputs, only four PWM inputs are
used, and the logical high/low states are routed to the
FETs as needed.
nPDN Input Pin
The nPDN pin is a control input that is used to set the
inactive (powered down) state, and also mute the
outputs. It operates by turning off drive and internal
sources to the PWM outputs, as well as turning off the
PWM drive to those outputs.
When an overcurrent condition is detected on an output,
causing its overcurrent protection to latch and turn off
that output, asserting the nPDN input resets the device,
and clears this overcurrent state.
The nPDN pin is active low, and inactive when at logic
high level.
nERRORA-D Output Pins
Each of the four outputs includes an overload and
overcurrent monitor. An overcurrent or overload
condition asserts the nERROR output for that channel.
These outputs are active low, open drain. Depending on
the output mode configuration and need to monitor more
than one output, these nERROR pins can be wire-or
connected together.
nOVRT Output Pin
The nOVRT pin is an output that provides warning of a
high temperature condition. It is an open drain, active
low output. This pin provides only indication of high
temperature.
IREF Pin
The IREF pin is used to control the overcurrent
monitoring threshold. A 100kΩ resistor connects from
this pin to ground.
11
D2-24044
OCFG0, OCFG1 Input Pins
These two pins are used to define the configuration of the
four output stages. They are connected to logic high
(PWMVDD) or logic ground (PWMGND) to set their level.
Refer to “Output Mode Configurations” on page 14 for
additional reference and definition.
Protection
The D2-24044 device includes monitors for protection of
the system as well as the device itself. Certain levels of
protection are managed on-chip, as shown in Figure 10.
Other protection is integrated at the system level
through the system controller, and involves system
design decisions based on:
• A short circuit, over-temperature, or undervoltage
• Other operation depends on the PWM/system
• Power supply sensors shut down the device if supply
• Overload and overcurrent monitors provide dual
• Chip temperature monitoring provides dual threshold
Short-Circuit and Overcurrent Sensing
Each PWM output FET includes a dual-threshold
overcurrent sensor. Multiple functions occur depending
on detection of overcurrent conditions:
• The lower threshold is used to monitor fault
• The higher threshold monitors fault conditions of the
• The nERROR output asserts for the channel detecting
• For the lower level threshold, nERROR remains
• For the higher level threshold, the output is shut
event will shut down the outputs.
controller to properly manage full system protection
operation.
voltages drop below their design thresholds.
threshold status of high current conditions, providing
both indication, and device shutdown if needed.
status of high temperature conditions, providing
both indication, and device shutdown if needed.
conditions after the output stage filter inductor, such
as shorts or overloads on the loudspeaker outputs.
PWM output pin.
the fault.
asserted only through the duration of the
overcurrent event.
down, and its nERROR output is asserted, and these
remain latched until the controller acknowledges the
fault event by turning off the channel’s PWM drive.
(When the output is shutdown, its PWM output pin
floats.)
September 3, 2010
FN7678.0