LCMXO256C-5TN100C LATTICE SEMICONDUCTOR, LCMXO256C-5TN100C Datasheet - Page 25
LCMXO256C-5TN100C
Manufacturer Part Number
LCMXO256C-5TN100C
Description
MACHXO PLD FLASH, SCRAM 1.8V, 256
Manufacturer
LATTICE SEMICONDUCTOR
Series
MachXOr
Datasheet
1.LCMXO1200C-5TN144C.pdf
(244 pages)
Specifications of LCMXO256C-5TN100C
Cpld Type
FLASH
No. Of Macrocells
128
No. Of I/o's
78
Propagation Delay
3.5ns
Global Clock Setup Time
1.3ns
Frequency
600MHz
Supply Voltage Range
1.71V To 3.465V
Operating
RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LCMXO256C-5TN100C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
- Current page: 25 of 244
- Download datasheet (9Mb)
Lattice Semiconductor
2. Left and Right sysIO Buffer Pairs
Typical I/O Behavior During Power-up
The internal power-on-reset (POR) signal is deactivated when V
After the POR signal is deactivated, the FPGA core logic becomes active. It is the user’s responsibility to ensure
that all V
Banks that are critical to the application. The default configuration of the I/O pins in a blank device is tri-state with a
weak pull-up to VCCIO. The I/O pins will maintain the blank configuration until VCC, VCCAUX and VCCIO have
reached satisfactory levels at which time the I/Os will take on the user-configured settings.
The V
fers. In order to simplify system design while providing consistent and predictable I/O behavior, the I/O buffers
should be powered up along with the FPGA core fabric. Therefore, V
together with the V
Supported Standards
The MachXO sysIO buffer supports both single-ended and differential standards. Single-ended standards can be
further subdivided into LVCMOS and LVTTL. The buffer supports the LVTTL, LVCMOS 1.2, 1.5, 1.8, 2.5, and 3.3V
standards. In the LVCMOS and LVTTL modes, the buffer has individually configurable options for drive strength,
bus maintenance (weak pull-up, weak pull-down, bus-keeper latch or none) and open drain. BLVDS and LVPECL
output emulation is supported on all devices. The MachXO1200 and MachXO2280 support on-chip LVDS output
buffers on approximately 50% of the I/Os on the left and right Banks. Differential receivers for LVDS, BLVDS and
LVPECL are supported on all Banks of MachXO1200 and MachXO2280 devices. PCI support is provided in the top
Banks of the MachXO1200 and MachXO2280 devices. Table 2-8 summarizes the I/O characteristics of the devices
in the MachXO family.
Tables 2-9 and 2-10 show the I/O standards (together with their supply and reference voltages) supported by the
MachXO devices. For further information on utilizing the sysIO buffer to support a variety of standards please see
the details of additional technical documentation at the end of this data sheet.
of the devices also support differential input buffers. PCI clamps are available on the top Bank I/O buffers. The
PCI clamp is enabled after V
figured.
The two pads in the pair are described as “true” and “comp”, where the true pad is associated with the positive
side of the differential input buffer and the comp (complementary) pad is associated with the negative side of
the differential input buffer.
The sysIO buffer pairs in the left and right Banks of the device consist of two single-ended output drivers and
two sets of single-ended input buffers (supporting ratioed and absolute input levels). The devices also have a
differential driver per output pair. The referenced input buffer can also be configured as a differential input buf-
fer. In these Banks the two pads in the pair are described as “true” and “comp”, where the true pad is associ-
ated with the positive side of the differential I/O, and the comp (complementary) pad is associated with the
negative side of the differential I/O.
CC
CCIO
and V
Banks are active with valid input logic levels to properly control the output logic states of all the I/O
CCAUX
CC
supply the power to the FPGA core fabric, whereas the V
and V
CCAUX
CC
supplies
, V
CCAUX
, and V
CCIO
2-16
are at valid operating levels and the device has been con-
CC
and V
CCIO
supplies should be powered up before or
CCAUX
MachXO Family Data Sheet
CCIO
have reached satisfactory levels.
supplies power to the I/O buf-
Architecture
Related parts for LCMXO256C-5TN100C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC, CPLD, FLASH, 256 MACROCELL, TQFP-100
Manufacturer:
LATTICE SEMICONDUCTOR
Part Number:
Description:
IC, CPLD, FLASH, 256 MACROCELL, TQFP-100
Manufacturer:
LATTICE SEMICONDUCTOR
Part Number:
Description:
CPLD MachXO Family 128 Macro Cells 1.8V/2.5V/3.3V 100-Pin TQFP Tray
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
ISPLSI2032-80LT44Lattice Semiconductor [In-System Programmable High Density PLD]
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
IC PROGRAMMED LATTICE GAL 16V8
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
Lattice Semiconductor Corp.
Datasheet: