MB95F264KPF-G-SNE2 Fujitsu, MB95F264KPF-G-SNE2 Datasheet - Page 5

• Manufacturer Part Number: MB95F264KPF-G-SNE2
• Description: MCU, 8BIT, 20K FLASH, 8FX, 20SOP
• Manufacturer: Fujitsu

Specifications of MB95F264KPF-G-SNE2

• No. Of I/o's: 17
• Ram Memory Size: 496Byte
• Cpu Speed: 16.25MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 2
• Core Size: 8bit
• Program Memory Size: 20KB
• Oscillator Type: Internal, External
• Controller Family/series: MB95260H

DS07–12627–6E
Parameter
Type
Clock
supervisor
counter
Program ROM
capacity
RAM capacity
Low-voltage
detection reset
Reset input
CPU functions
General-
purpose I/O
Timebase timer Interrupt cycle : 0.256 ms to 8.3 s (when external clock = 4 MHz)
Hardware/
software
watchdog timer
Wild register
LIN-UART
8/10-bit A/D
converter
8/16-bit
composite
timer
External
interrupt
On-chip debug
Watch
prescaler
Flash memory
Standby mode Sleep mode, stop mode, watch mode, timebase timer mode
Package
• MB95270H Series
Part number
It supervises the main clock oscillation.
Number of basic instructions
Instruction bit length
Instruction length
Data bit length
Minimum instruction execution time : 61.5 ns (with machine clock = 16.25 MHz)
Interrupt processing time
I/O ports (Max): 4
CMOS I/O: 3
N-ch open drain: 1
Reset generation cycle
Main oscillation clock at 10 MHz: 105 ms (Min)
The sub-internal CR clock can be used as the source clock of the hardware watchdog timer.
It can be used to replace three bytes of data.
No LIN-UART
2 channels
8-bit or 10-bit resolution can be selected.
1 channel
The timer can be configured as an "8-bit timer × 2 channels" or a "16-bit timer × 1 channel".
It has built-in timer function, PWC function, PWM function and input capture function.
Count clock: it can be selected from internal clocks (seven types) and external clocks.
It can output square wave.
2 channels
Interrupt by edge detection (The rising edge, falling edge, or both edges can be selected.)
It can be used to wake up the device from standby modes.
1-wire serial control
It supports serial writing. (asynchronous mode)
Eight different time intervals can be selected.
It supports automatic programming, Embedded Algorithm,
write/erase/erase-suspend/erase-resume commands.
It has a flag indicating the completion of the operation of Embedded Algorithm.
Number of write/erase cycles : 100000
Data retention time: 20 years
Flash security feature for protecting the content of the Flash memory
MB95F272H
240 bytes
8 Kbytes
MB95F273H
Dedicated
12 Kbytes
496 bytes
No
MB95260H/270H/280H Series
MB95F274H
20 Kbytes
496 bytes
Flash memory product
: 136
: 8 bits
: 1 to 3 bytes
: 1, 8 and 16 bits
: 0.6 µs (with machine clock = 16.25 MHz)
FPT-8P-M08
DIP-8P-M03
I/O ports (Max): 5
CMOS I/O: 3
N-ch open drain: 2
MB95F272K
240 bytes
8 Kbytes
Selected by software
MB95F273K
12 Kbytes
496 bytes
Yes
MB95F274K
20 Kbytes
496 bytes
5