LTC3675EUFF#PBF Linear Technology, LTC3675EUFF#PBF Datasheet - Page 28
![IC, PMIC, 1A, QFN-44](/photos/19/3/190363/4243289_sml.jpg)
LTC3675EUFF#PBF
Manufacturer Part Number
LTC3675EUFF#PBF
Description
IC, PMIC, 1A, QFN-44
Manufacturer
Linear Technology
Datasheet
1.LTC3675EUFFPBF.pdf
(36 pages)
Specifications of LTC3675EUFF#PBF
Supply Voltage
5.5V
No. Of Step-down Dc - Dc Converters
4
No. Of Ldo Regulators
1
Digital Ic Case Style
QFN
No. Of Pins
44
No. Of Regulated Outputs
7
Operating Temperature Range
-40°C To +125°C
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS INFORMATION
LTC3675
Optional capacitor C
loop stability.
Buck-Boost Regulator
The buck-boost regulator is an internally compensated
voltage mode regulator that is designed to be used with
a 2.2μH inductor. Recommended inductors are listed in
the Table 8.
The input supply needs to be decoupled with a 10μF
capacitor while the output needs to be decoupled with
a 22μF capacitor. Refer to “Capacitor Selection” in the
Applications Information section for details on selecting
a proper capacitor.
The buck-boost regulator can be programmed via I
program the buck-boost regulator, use sub-address 06h.
The bit format is explained in Table 10.
Table 10. Buck-Boost Regulator Program Register Bit Format
Bit7
Bit6
Bit5
Bit4
Bit3(DAC3)
Bit2(DAC2)
Bit1(DAC1)
Bit0(DAC0)
Table 12. Recommended Schottky Diodes for LED Driver
PART NUMBER
PD3S140
ZLLS1000
CTLSH1-40M322
Table 11. Recommended Inductors for LED Driver
PART NUMBER
LPS6225-103M
IHLP2020BZER10RM01
28
Enable
x
Mode
Slow edge
DAC control
FF
is not needed and may compromise
Default is ‘0’ which disables the buck-boost. The buck-boost regulator can alternately be enabled via its enable pin.
When enabled via pin, the contents of the I
Unused
Mode = 0 is PWM mode, Mode = 1 is Burst Mode operation. Default is ‘0.’
This bit controls the slew rate of the switch node. Default is ‘0’ which enables the switch node to slew at a faster rate
than if the bit were programmed a ‘1.’
These bits are used to program the feedback regulation voltage. Default is ‘1111’ which programs a full-scale voltage of
800mV. Bits ‘0000’ program the lowest feedback regulation of 425mV. A LSB (DAC0) has a bit weight of 25mV.
L(μH)
I
1.16
F
1.0
1.0
10
10
(A)
MANUFACTURER
Diodes Inc.
www.diodes.com
Diodes Inc./Zetex
www.diodes.com
Central Semiconductor
www.centralsemi.com
MAX I
2.1
4
DC
(A)
2
C. To
MAX DCR (mΩ)
105
184
2
C register program its functionality.
To ensure loop stability, feedback resistor R1 in Figure 5
should be no greater than 105kΩ. Optional capacitor C
is not needed and may compromise loop stability.
LED Driver
For proper operation the LED driver boost circuit needs
a 10μH inductor. Recommended inductors are listed in
Table 11.
The LED driver also needs a rectifi er diode. Recommended
schottky diodes are listed in Table 12.
The LED driver has two registers that can be programmed
via I
07h and the bit format is as shown in Table 13.
The rate at which the gradation circuit ramps the LED cur-
rent is set by GRAD[2:0]. GRAD[2:0] sets the time the LED
driver will take to transition through one LSB of LED current.
2
C. One of the registers is accessed at sub-address
SIZE IN mm (L × W × H)
5.2 × 5.5 × 2
6 × 6 × 2.5
MANUFACTURER
Coilcraft
www.coilcraft.com
Vishay
www.vishay.com
3675f
FF