PIC18C601-I/L Microchip Technology, PIC18C601-I/L Datasheet - Page 165

• Manufacturer Part Number: PIC18C601-I/L
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LDCC,68PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C601-I/L

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Type: ROMless
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: 3-Wire, I2C, SPI, USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 47
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DV164005, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164309 - MODULE SKT FOR PM3 44PLCCXLT68L1 - SOCKET TRANSITION ICE 68PLCCAC174007 - MODULE SKT PROMATEII 68PLCC
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C601I/L

FIGURE 15-12:
15.4.6
To initiate a START condition, the user sets the START
Condition Enable (SEN) bit (SSPCON2 register). If the
SDA and SCL pins are sampled high, the baud rate
generator
SSPADD<6:0> and starts its count. If SCL and SDA are
both sampled high when the baud rate generator times
out (T
SDA being driven low while SCL is high, is the START
condition, and causes the S bit (SSPSTAT register) to
be set. Following this, the baud rate generator is
reloaded with the contents of SSPADD<6:0> and
resumes its count. When the baud rate generator times
out (T
automatically cleared by hardware, the baud rate gen-
erator is suspended leaving the SDA line held low and
the START condition is complete.
FIGURE 15-13:
2001 Microchip Technology Inc.
BRG
BRG
), the SDA pin is driven low. The action of the
), the SEN bit (SSPCON2 register) will be
I
CONDITION TIMING
is
2
C MASTER MODE START
SDA
SCL
BRG
value
BRG
reload
re-loaded
Write to SEN bit occurs here
BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
FIRST START BIT TIMING
with
03h
SDA
SCL
DX
the
SCL de-asserted but slave holds
SCL low (clock arbitration)
02h
SCL is sampled high, reload takes
place and BRG starts its count
contents
Advance Information
SDA = 1,
SCL = 1
T
BRG
01h
of
Set S bit (SSPSTAT)
T
S
BRG
BRG decrements on
Q2 and Q4 cycles
00h (hold off)
DX-1
At completion of START bit,
Hardware clears SEN bit
15.4.6.1
If the user writes the SSPBUF when a START
sequence is in progress, the WCOL is set and the con-
tents of the buffer are unchanged (the write doesn’t
occur).
and sets SSPIF bit
Note:
Note:
T
Write to SSPBUF occurs here
BRG
1st bit
If at the beginning of the START condition,
the SDA and SCL pins are already sam-
pled low, or if during the START condition
the SCL line is sampled low before the
SDA line is driven low, a bus collision
occurs, the Bus Collision Interrupt Flag
BCLIF is set, the START condition is
aborted, and the I
IDLE state.
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the START
condition is complete.
WCOL Status Flag
SCL allowed to transition high
PIC18C601/801
T
03h
BRG
02h
2nd bit
2
C module is reset into its
DS39541A-page 165