PIC18F6722-E/PT Microchip Technology, PIC18F6722-E/PT Datasheet - Page 12

• Manufacturer Part Number: PIC18F6722-E/PT
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6722-E/PT

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-TFQFP
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11
• Lead Free Status / Rohs Status: Details

PIC18F6627/6722/8627/8722
37. Module: Reset
DS80221C-page 12
This version of silicon does not support the func-
tionality described in Note 1 of parameter D002 in
Section 28.1 “DC Characteristics: Supply
Voltage” of the data sheet. The RAM content may
be altered during a Reset event if the following
conditions are met.
• Device is accessing RAM.
• Asynchronous Reset (i.e., WDT, BOR or MCLR
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
occurs when a write operation is being
executed (start of a Q4 cycle).
38. Module: External Memory Bus
The A<19:16> EMB address lines and Read/Write
control pins (OE, WRH and WRL) are released to
their respective inactive states at the same time,
violating the timing condition mentioned in
Figure 28-8 and Figure 28-9 in the Device Data
Sheet. This may result in a peripheral device on
the bus detecting an address change when a write/
read is initiated. The bus capacitance and signal
delay on the address and control lines can affect
the probability of invalid detection.
Work around
Two work arounds are available:
1. Use a latch based on the falling edge of ALE to
2. Add a delay circuit to extend the valid time for
hold the A<19:16> signals.
A<19:16> signals to ensure the address is
valid until read/write signals go inactive.
© 2006 Microchip Technology Inc.