ADUC7060BCPZ32 Analog Devices Inc, ADUC7060BCPZ32 Datasheet - Page 75

• Manufacturer Part Number: ADUC7060BCPZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BCPZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 84. PWMCON MMR Bit Designations
Bit
15
14
13
12
11
10
9
8:6
5
4
3
2
1
0
1
In H-bridge mode, HMODE = 1. See Table 85 to determine the PWM outputs.
Name
Reserved
Sync
PWM5INV
PWM3INV
PWM1INV
PWMTRIP
ENA
PWMCP[2:0]
POINV
HOFF
LCOMP
DIR
HMODE
PWMEN
Description
This bit is reserved. Do not write to this bit.
Enables PWM synchronization.
Set to 1 by user so that all PWM counters are reset on the next clock edge after the detection of a high-to-low
transition on the P1.2/SYNC pin.
Cleared by user to ignore transitions on the P1.2/SYNC pin.
Set to 1 by user to invert PWM5.
Cleared by user to use PWM5 in normal mode.
Set to 1 by user to invert PWM3.
Cleared by user to use PWM3 in normal mode.
Set to 1 by user to invert PWM1.
Cleared by user to use PWM1 in normal mode.
Set to 1 by user to enable PWM trip interrupt. When the PWM trip input (Pin P1.3/TRIP) is low, the PWMEN bit is
cleared and an interrupt is generated.
Cleared by user to disable the PWMTRIP interrupt.
If HOFF = 0 and HMODE = 1. Note that, if not in H-bridge mode, this bit has no effect.
Set to 1 by user to enable PWM outputs.
Cleared by user to disable PWM outputs.
If HOFF = 1 and HMODE = 1, see Table 85.
PWM clock prescaler bits. Sets the UCLK divider.
[000] = UCLK/2.
[001] = UCLK/4.
[010] = UCLK/8.
[011] = UCLK/16.
[100] = UCLK/32.
[101] = UCLK/64.
[110] = UCLK/128.
[111] = UCLK/256.
Set to 1 by user to invert all PWM outputs.
Cleared by user to use PWM outputs as normal.
High side off.
Set to 1 by user to force PWM0 and PWM2 outputs high. This also forces PWM1 and PWM3 low.
Cleared by user to use the PWM outputs as normal.
Load compare registers.
Set to 1 by user to load the internal compare registers with the values in PWMxCOMx on the next transition of the
PWM timer from 0x00 to 0x01.
Cleared by user to use the values previously stored in the internal compare registers.
Direction control.
Set to 1 by user to enable PWM0 and PWM1 as the output signals while PWM2 and PWM3 are held low.
Cleared by user to enable PWM2 and PWM3 as the output signals while PWM0 and PWM1 are held low.
Enables H-bridge mode.
Set to 1 by user to enable H-bridge mode and Bit 1 to Bit 5 of PWMCON.
Cleared by user to operate the PWMs in standard mode.
Set to 1 by user to enable all PWM outputs.
Cleared by user to disable all PWM outputs.
1
Rev. B | Page 75 of 108
ADuC7060/ADuC7061