ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 104

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ADuC7060/ADuC7061
HARDWARE DESIGN CONSIDERATIONS
POWER SUPPLIES
The ADuC706x operational power supply voltage range is
2.375 V to 2.625 V. Separate analog and digital power supply
pins (AVDD and DVDD, respectively) allow AVDD to be kept
relatively free of noisy digital signals often present on the
system DVDD line. In this mode, the part can also operate with
split supplies; that is, it can use different voltage levels for each
supply. For example, the system can be designed to operate
with a DVDD voltage level of 2.6 V, whereas the AVDD level
can be at 2.5 V or vice versa. A typical split supply
configuration is shown in Figure 28.
As an alternative to providing two separate power supplies, the
user can reduce noise on AVDD by placing a small series
resistor and/or ferrite bead between AVDD and DVDD, and then
decoupling AVDD separately to ground. An example of this
configuration is shown in
other analog circuitry (such as op amps, voltage reference, and
others) can be powered from the AVDD supply line as well.
DIGITAL
SUPPLY
+
–
0.1µF
Figure 28. External Dual Supply Connections
10µF
DVDD
DGND
Figure 29. With this configuration,
ADuC7060/
ADuC7061
AGND
AVDD
10µF
ANALOG
SUPPLY
0.1µF
+
–
Rev. C | Page 104 of 108
Notice that in both Figure 28 and Figure 29, a large value (10 μF)
reservoir capacitor sits on DVDD, and a separate 10 μF
capacitor sits on AVDD. In addition, local, small value (0.1 μF)
capacitors are located at each AVDD and DVDD pin of the chip.
As per standard design practice, be sure to include all of these
capacitors and ensure that the smaller capacitors are close to the
AVDD pin with trace lengths as short as possible. Connect the
ground terminal of each of these capacitors directly to the
underlying ground plane.
Note that the analog and digital ground pins on the ADuC706x
must be referenced to the same system ground reference point
at all times.
Finally, note that, when the DVDD supply reaches 1.8 V, it must
ramp to 2.25 V in less than 128 ms. This is a requirement of the
internal power-on reset circuitry.
DIGITAL
SUPPLY
+
–
0.1µF
Figure 29. External Single Supply Connections
10µF
DVDD
DGND
ADuC7060/
ADuC7061
BEAD
AGND
AVDD
10µF
ANALOG
SUPPLY
0.1µF