ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 46

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ADuC7060/ADuC7061
Auxiliary ADC Control Register
Name:
Address:
Default value:
Access:
Function:
Table 44. ADC1CON MMR Bit Designations
Bit
15
14:13
12
11
10:7
Name
ADC1EN
ADC1DIAG[1:0]
HIGHEXTREF1
ADC1CODE
ADC1CH[3:0]
ADC1CON
0xFFFF0510
0x0000
Read and write
The auxiliary ADC control MMR is a 16-bit register.
Description
Auxiliary channel ADC enable.
Diagnostic current source enable bits. This is the same current source as that used on ADC0DIAG[1:0]. The
ADCs cannot enable the diagnostic current sources at the same time.
[00]= current sources off.
[01] = enables a 50 μA current source on selected positive input (for example, ADC2).
[10] = enables a 50 μ A current source on selected negative input (for example, ADC3).
[11] = enables a 50 μ A current source on both selected inputs (for example, ADC2 and ADC3).
This bit must be set high if the external reference for ADC1 exceeds 1.35 V. This results in the reference
source being divided by 2.
Clear this bit when using the internal reference or an external reference of less than 1.35 V.
Auxiliary channel ADC output coding.
This bit is set to 1 by user code to configure auxiliary ADC output coding as unipolar.
This bit is cleared to 0 by user code to configure auxiliary ADC output coding as twos complement.
Auxiliary channel ADC input select. Note: Single-ended channels are selected with respect to ADC5. Bias
ADC5 to a minimum level of 0.1 V.
[0000] = ADC2/ADC3 (differential mode).
[0001] = ADC4/ADC5 (differential mode).
[0010] = ADC6/ADC7 (differential mode).
[0011] = ADC8/ADC9 (differential mode).
[0100] = ADC2/ADC5 (single-ended mode).
[0101] = ADC3/ADC5 (single-ended mode).
[0110] = ADC4/ADC5 (single-ended mode).
[0111] = ADC6/ADC5 (single-ended mode).
[1000] = ADC7/ADC5 (single-ended mode).
[1001] = ADC8/ADC5 (single-ended mode).
[1010] = ADC9/ADC5 (single-ended mode).
[1011] = internal temperature sensor+/internal temperature sensor−.
[1100] = VREF+, VREF−. Note: This is the reference selected by the ADC1REF bits.
[1101] = DAC_OUT/AGND.
[1110] = undefined.
[1111] = internal short to ADC3.
This bit is set to 1 by user code to enable the auxiliary ADC.
Clearing this bit to 0 powers down the auxiliary ADC.
Rev. C | Page 46 of 108