CS47048C-CQZ Cirrus Logic Inc, CS47048C-CQZ Datasheet - Page 27
![IC 4CH ADC 8ch DAC & 32bit DSP](/photos/28/17/281780/cs47048c-cqz_sml.jpg)
CS47048C-CQZ
Manufacturer Part Number
CS47048C-CQZ
Description
IC 4CH ADC 8ch DAC & 32bit DSP
Manufacturer
Cirrus Logic Inc
Type
Fixed Pointr
Specifications of CS47048C-CQZ
Interface
I²C, SPI
Clock Rate
150MHz
On-chip Ram
128kB
Voltage - I/o
3.30V
Voltage - Core
1.80V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
100-LQFP Exposed Pad, 100-eLQFP, 100-HLQFP
Operating Temperature Range
0°C To +70°C
No. Of Pins
100
Frequency
147MHz
Embedded Interface Type
I2C, SPI
Core Supply Voltage
1.89V
No. Of Mips
150
Digital Ic Case Style
LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
598-1539 - BOARD EVAL 4CH ADC/8CH DAC DSP598-1536 - BOARD EVAL 4CH ADC/8CH DAC DSP
Non-volatile Memory
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
598-1657
CS47048B-CQZ
CS47048B-CQZ
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS47048C-CQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
135
Company:
Part Number:
CS47048C-CQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Company:
Part Number:
CS47048C-CQZR
Manufacturer:
CIRRUS
Quantity:
1 400
Company:
Part Number:
CS47048C-CQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS47048C-CQZR
Manufacturer:
CIRRUSLOGIC
Quantity:
20 000
5.16 ADC Characteristics
5.16.1 Analog Input Characteristics (Commercial)
Test Conditions (unless otherwise specified): T
wave driven through the passive input filter (R
ning test application; Measurement Bandwidth is 10 Hz to 20 kHz.
DS787PP5
Fs= 96 kHz
Dynamic Range
Total Harmonic Distortion + Noise
AIN_1A/B Interchannel Isolation
AIN_[2.6]A/B MUX Interchannel Isolation
DC Accuracy
Interchannel Gain Mismatch
Gain Drift
Analog Input
Full-Scale Input Voltage
Differential Input Impedance
Single-Ended Input Impedance
Common Mode Rejection Ratio (CMRR)
Parasitic Load Capacitance (C
1. dB units referred to the typical full-scale voltage.
2. These full-scale values were measured with R
3. The full-scale voltage can be changed be scaling R
4. Measured between AIN_xx+ and AN_xx-.
5. Measured between AIN_xx+ and AGND.
6. Decreasing Full-Scale voltage by reducing R
7. Common mode input current should be kept to less than +/- 160uA to avoid performance degradation: |(I
8. This number was measured using perfectly matched external resistors (R
9. C
10. This measurement is not applicable to the CS47028 and CS47024 devices.
Differential Full-Scale (Vpp) =3.7*VDDA*(R
Single-Ended Full-Scale (Vpp) = 1.85*VDDA*(R
160uA. This corresponds to +/- 1.6V for R
typically reduce CMRR by 20 log (|
package.
L
represents the parasitic load capacitance between R
40 kHz bandwidth
40 kHz bandwidth unweighted
Parameter
1,6,7
2,3
4
L
5
)
unweighted
A-weighted
10
9
6,7
-20 dB
-60 dB
-1 dB
-1 dB
R
i
8
|/R
i
i
Copyright 2011 Cirrus Logic
=10 k in the differential case.
+ 0.001).
i
+200)/(10k+200)
i
=10 k) in
A
i
Min
will cause the noise floor to increase.
i
=10k for both the single-ended and differential mode input circuits.
= 0 to +70C; VDD = 1.8V±5%, VDDA (VA)= 3.3V±5%; 1 kHz sine
3.3
99
96
-
-
-
-
-
-
-
-
-
-
-
-
-
i
+200)/(10k+200)
i
.
Differential
3.7•VA
i
±120
Figure 14 on page 29
on the input circuit and the input pin of the CS47048
Typ
105
102
400
-98
-82
-42
-90
0.1
99
95
95
60
-
-
Max
-92
3.9
20
-
-
-
-
-
-
-
-
-
-
-
-
-
i
). Mismatch in the external resistors will
Min
1.65
96
93
or
-
-
-
-
-
-
-
-
-
-
-
-
Figure 15 on page
Single-Ended
1.85•VA
±120
Audio SOC Processor Family
Typ
102
200
-95
-79
-39
-90
0.1
99
96
95
95
-
-
-
CS470xx Data Sheet
1.95
Max
-89
20
-
-
-
-
-
-
-
-
-
-
-
-
-
ip
29; DSP run-
+I
in
)/2| <
ppm/°C
Unit
V
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
pF
PP
27