JN5139-001-M/04R1T NXP Semiconductors, JN5139-001-M/04R1T Datasheet - Page 4

• Manufacturer Part Number: JN5139-001-M/04R1T
• Description: JN5139-001-M/SOM041/REEL13 DP
• Manufacturer: NXP Semiconductors
• Series: JN5139-001-M0xRr

Specifications of JN5139-001-M/04R1T

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: Home/Building Automation, Industrial Control and Monitoring
• Power - Output: 19dBm
• Sensitivity: -97dBm
• Voltage - Supply: 2.7 V ~ 3.6 V
• Current - Receiving: 45mA
• Current - Transmitting: 120mA
• Data Interface: PCB, Surface Mount
• Memory Size: 96kB RAM, 192kB ROM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -20°C ~ 70°C
• Package / Case: Module
• Core: RISC
• Interface Type: SPI, UART
• Core Architecture: RISC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Details
• Other names: 616-1041-2; 935294017534; JN5139-001-M04; JN5139-001-M04R1T; JN5139-001-M04R1T; Q3424158

2. Specifications
Most specification parameters for the modules are specified in the chip datasheet - JN-DS- JN5139 Wireless
Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here.
VDD=3.0V @ +25°C
Deep sleep current
Sleep current
Radio transmit current
Radio receive current
Centre frequency accuracy
Receive sensitivity
Maximum Transmit power
Maximum Transmit power [Boost Mode]
Transmit power at 3.6V
Maximum input signal
RSSI range
RF Port impedance – SMA/uFl connector
VSWR (max)
Master SPI port
Slave SPI port
Two UARTs
Two-wire serial I/F (compatible with SMbus & I
Two programmable Timer/Counters with
capture/compare facility, Tick timer
Two programmable Sleep Timers
Digital IO lines (multiplexed with UARTs, timers
and SPI selects)
Four channel Analogue-to-Digital converter
Two channel Digital-to-Analogue converter
Two programmable analogue comparators
Internal temperature sensor and battery monitor
The performance of all peripherals is defined in the JN-DS- JN5139 Wireless Microcontroller Datasheet [2]
Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated
antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity.
4
Typical DC Characteristics
Typical RF Characteristics
Peripherals
JN-DS-JN5139-xxx-Myy 1v6
2
C)
JN5139-xxx-
M00/01/03
+/-25ppm
-95 to -10
+2.5dBm
5 selects
+10dBm
-96dBm
50 ohm
+1dBm
1.3uA
2.6uA
37mA
37mA
dBm
2:1
21
JN5139-xxx-
-105 to -20
+/-25ppm
-102dBm
17.5dBm
3 selects
+10dBm
M02/04
50 ohm
125mA
19dBm
1.3uA
2.6uA
45mA
dBm
N/A
2:1
19
© NXP Laboratories UK 2010
With active sleep timer
CPU in doze, radio transmitting
CPU in doze, radio receiving
Additional +/-15ppm allowance for
temperature and ageing
Nominal for 1% PER, as per
802.15.4 section 6.5.3.3 (Note 1)
Nominal (Note 1)
(Note 1)
With Vdd=3.6V
For 1% PER, measured as
sensitivity
2.4 - 2.5GHz
2.4 - 2.5GHz
250kHz - 16MHz
250kHz - 8MHz
16550 compatible
Up to 400kHz
16MHz clock
32kHz clock
12-bit, up to 100ks/s
11-bit, up to 100ks/s
Ultra low power mode for sleep
Notes
Notes
Notes