JN5139-001-M/04R1T NXP Semiconductors, JN5139-001-M/04R1T Datasheet - Page 8

• Manufacturer Part Number: JN5139-001-M/04R1T
• Description: JN5139-001-M/SOM041/REEL13 DP
• Manufacturer: NXP Semiconductors
• Series: JN5139-001-M0xRr

Specifications of JN5139-001-M/04R1T

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: Home/Building Automation, Industrial Control and Monitoring
• Power - Output: 19dBm
• Sensitivity: -97dBm
• Voltage - Supply: 2.7 V ~ 3.6 V
• Current - Receiving: 45mA
• Current - Transmitting: 120mA
• Data Interface: PCB, Surface Mount
• Memory Size: 96kB RAM, 192kB ROM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -20°C ~ 70°C
• Package / Case: Module
• Core: RISC
• Interface Type: SPI, UART
• Core Architecture: RISC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Details
• Other names: 616-1041-2; 935294017534; JN5139-001-M04; JN5139-001-M04R1T; JN5139-001-M04R1T; Q3424158

*: These two pins are not connected for High power modules
4.2. Pin Descriptions
All pins behave as described in the JN-DS- JN5139 Wireless Microcontroller Datasheet [2], with the exception of the
following:
A single power supply pin, VDD is provided. Separate analogue (VSSA) and digital (GND) grounds are provided.
These should be connected together at the module pins.
SPISWP is a write protect pin for the serial flash memory. This should be held low to inhibit writes to the flash device.
SPISSZ is connected to SPI Slave Select 0 on the JN5139.
SPISSM is connected to the Slave Select pin on the memory.
This configuration allows the flash memory device to be programmed using an external SPI programmer if required.
For programming in this mode, the JN5139 should be held in reset by taking RESETN low.
The memory can also be programmed over the UART by using the flash programmer software provided by Jennic.
This is available as part of the Software Developer kit and libraries available from www.nxp.com/jennic. To enter
this programming mode, SPIMISO (pin 7) should be held low whilst the chip is reset. Once programming has finished,
the chip should be reset, when it will execute the new code downloaded.
For normal operation of the module and programming over the UART, SPISSZ should be connected to
SPISSM.
8
31
32
33
34a
35
36
37
38
39
40
41
Pin
4.2.1
4.2.2
Signal
SIF_D
DIO 16
CTS1
RTS1
TXD1
RXD1
COMP1-
COMP1+
ADC1
ADC2
ADC3
Power Supplies
SPI Memory Connections
Function
Serial Interface data / Intelligent peripheral data
out (output)
Intelligent peripheral device data in (input)
UART1 Clear To Send (input) / Intelligent
peripheral device select (input)
UART1 Request To Send (output) / Intelligent
peripheral interrupt (output)
UART1 Transmit Data (output)
UART1 Receive Data (input)
Comparator 1 inputs
Analogue to Digital input
Analogue to Digital input
Analogue to Digital input
JN-DS-JN5139-xxx-Myy 1v6
Alternative Function
General Purpose Digital I/O DIO15
General Purpose Digital I/O
General Purpose Digital I/O DIO17
General Purpose Digital I/O DIO18
General Purpose Digital I/O DIO19
General Purpose Digital I/O DIO20
© NXP Laboratories UK 2010