COM20019I3V-DZD SMSC, COM20019I3V-DZD Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/6/617/smsc_sml.jpg)
COM20019I3V-DZD
Manufacturer Part Number
COM20019I3V-DZD
Description
Network Controller & Processor ICs ARCNET Contrllr
Manufacturer
SMSC
Datasheet
1.COM20019I3V-HT.pdf
(70 pages)
Specifications of COM20019I3V-DZD
Product
Controller Area Network (CAN)
Number Of Transceivers
1
Data Rate
312.5 Kbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
3 V
Supply Current (max)
25 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
PLCC-28
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
5.1
Rev. 11-07-08
MICROCONTROLLER INTERFACE
The top halves of Figure 5.1 and Figure 5.2 illustrate typical COM20019I 3V interfaces to the
microcontrollers. The interfaces consist of a 8-bit data bus, an address bus and a control bus. In order to
support a wide range of microcontrollers without requiring glue logic and without increasing the number of
pins, the COM20019I 3V automatically detects and adapts to the type of microcontroller being used. Upon
hardware reset, the COM20019I 3V first determines whether the read and write control signals are
separate READ and WRITE signals (like the 80XX) or DIRECTION and DATA STROBE (like the 68XX).
To determine the type of control signals, the device requires the software to execute at least one write
access to external memory before attempting to access the COM20019I 3V. The device defaults to 80XX-
like signals. Once the type of control signals are determined, the COM20019I 3V remains in this interface
mode until the next hardware reset occurs. The second determination the COM20019I 3V makes is
whether the bus is multiplexed or non-multiplexed. To determine the type of bus, the device requires the
software to write to an odd memory location followed by a read from an odd location before attempting to
access the COM20019I 3V. The signal on the A0 pin during the odd location access tells the COM20019I
3V the type of bus. Since multiplexed operation requires A0 to be active low, activity on the A0 line tells
the COM20019I 3V that the bus is non-multiplexed. The device defaults to multiplexed operation. Both
determinations may be made simultaneously by performing a WRITE followed by a READ operation to an
odd location within the COM20019I 3V Address space 20019 registers.
determined, the COM20019I 3V remains in this interface mode until hardware reset occurs.
Whenever nCS and nRD are activated, the preset determinations are assumed as final and will not be
changed until hardware reset. Refer to Description of Pin Functions section for details on the related
signals. All accesses to the internal RAM and the internal registers are controlled by the COM20019I 3V.
The internal RAM is accessed via a pointer-based scheme (refer to the Sequential Access Memory
section), and the internal registers are accessed via direct addressing. Many peripherals are not fast
enough to take advantage of high-speed microcontrollers. Since microcontrollers do not typically have
READY inputs, standard peripherals cannot extend cycles to extend the access time. The access time of
the COM20019I 3V, on the other hand, is so fast that it does not need to limit the speed of the
microcontroller.
microcontroller speed.
The COM20019I 3V provides for no wait state arbitration via direct addressing to its internal registers and
a pointer based addressing scheme to access its internal RAM. The pointer may be used in auto-
increment mode for typical sequential buffer emptying or loading, or it can be taken out of auto-increment
mode to perform random accesses to the RAM. The data within the RAM is accessed through the data
register. Data being read is prefetched from memory and placed into the data register for the
microcontroller to read. It is important to notice that only by writing a new address pointer (writing to an
address pointer low), one obtains the contents of COM20019I 3V internal RAM. Performing only read from
the Data Register does not load new data from the internal RAM. During a write operation, the data is
stored in the data register and then written into memory. Whenever the pointer is loaded for reads with a
new value, data is immediately prefetched to prepare for the first read operation.
Chapter 5
The COM20019I 3V is designed to be flexible so that it is independent of the
System Description
DATASHEET
Page 16
Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
Once the type of bus is
SMSC COM20019I 3.3V Rev.C