PIC12LF1822T-I/SN Microchip Technology, PIC12LF1822T-I/SN Datasheet - Page 122

• Manufacturer Part Number: PIC12LF1822T-I/SN
• Description: 3.5 KB Flash, 128 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Na
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 12Fr

Specifications of PIC12LF1822T-I/SN

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: PIC12LF
• Core: PIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC12F/LF1822/PIC16F/LF1823
12.2
PORTA is a 6-bit wide, bidirectional port. The
corresponding data direction register is TRISA
(Register
corresponding PORTA pin an input (i.e., disable the
output driver). Clearing a TRISA bit (= 0) will make the
corresponding PORTA pin an output (i.e., enables
output driver and puts the contents of the output latch
on the selected pin). The exception is RA3, which is
input only and its TRIS bit will always read as ‘1’.
Example 12-1
Reading the PORTA register
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then
written to the PORT data latch (LATA).
The TRISA register
PORTA pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits
in the TRISA register are maintained set when using
them as analog inputs. I/O pins configured as analog
input always read ‘0’.
12.2.1
The ANSELA register
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELA bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELA bits has no affect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
EXAMPLE 12-1:
DS41413B-page 122
BANKSEL
CLRF
BANKSEL
CLRF
BANKSEL
CLRF
BANKSEL
MOVLW
MOVWF
Note:
PORTA Registers
12-3). Setting a TRISA bit (= 1) will make the
PORTA
PORTA
LATA
LATA
ANSELA
ANSELA
TRISA
B'00111000' ;Set RA<5:3> as inputs
TRISA
ANSELA REGISTER
The ANSELA register must be initialized
to configure an analog channel as a digital
input. Pins configured as analog inputs
will read ‘0’.
shows how to initialize PORTA.
INITIALIZING PORTA
(Register
(Register
;
;Init PORTA
;Data Latch
;
;
;digital I/O
;
;and set RA<2:0> as
;outputs
(Register
12-3) controls the
12-5) is used to
12-2) reads the
Preliminary
 2010 Microchip Technology Inc.