PIC18F43K20-E/MV Microchip Technology, PIC18F43K20-E/MV Datasheet - Page 256

• Manufacturer Part Number: PIC18F43K20-E/MV
• Description: 8KB, Flash, 768bytes-RAM, 36I/O, 8-bit Family,nanowatt XLP 40 UQFN 5x5x0.5mm TUB
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F43K20-E/MV

• Processor Series: PIC18
• Core: PIC18F
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 512 B
• Interface Type: I2C, SPI, SCI, USB, MSSP, RJ11
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: UQFN-40
• Development Tools By Supplier: MPLAB Integrated Development Environment
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 125 C
• Supply Current (max): 30 uA
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Lead Free Status / Rohs Status: Details

PIC18F2XK20/4XK20
18.3.4
The EUSART module has the capability of sending the
special Break character sequences that are required by
the LIN bus standard. A Break character consists of a
Start bit, followed by 12 ‘0’ bits and a Stop bit.
To send a Break character, set the SENDB and TXEN
bits of the TXSTA register. The Break character trans-
mission is then initiated by a write to the TXREG. The
value of data written to TXREG will be ignored and all
‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN specification).
The TRMT bit of the TXSTA register indicates when the
transmit operation is active or Idle, just as it does during
normal transmission. See Figure 18-9 for the timing of
the Break character sequence.
18.3.4.1
The following sequence will start a message frame
header made up of a Break, followed by an auto-baud
Sync byte. This sequence is typical of a LIN bus
master.
1.
2.
3.
4.
5.
FIGURE 18-9:
DS41303G-page 256
Reg. Empty Flag)
Write to TXREG
(Transmit Shift
Configure the EUSART for the desired mode.
Set the TXEN and SENDB bits to enable the
Break sequence.
Load the TXREG with a dummy character to
initiate transmission (the value is ignored).
Write ‘55h’ to TXREG to load the Sync character
into the transmit FIFO buffer.
After the Break has been sent, the SENDB bit is
reset by hardware and the Sync character is
then transmitted.
interrupt Flag)
(send Break
BRG Output
(Shift Clock)
control bit)
(Transmit
TRMT bit
TX (pin)
TXIF bit
SENDB
BREAK CHARACTER SEQUENCE
Break and Sync Transmit Sequence
SEND BREAK CHARACTER SEQUENCE
Dummy Write
SENDB Sampled Here
Start bit
bit 0
bit 1
Break
When the TXREG becomes empty, as indicated by the
TXIF, the next data byte can be written to TXREG.
18.3.5
The Enhanced EUSART module can receive a Break
character in two ways.
The first method to detect a Break character uses the
FERR bit of the RCSTA register and the Received data
as indicated by RCREG. The Baud Rate Generator is
assumed to have been initialized to the expected baud
rate.
A Break character has been received when;
• RCIF bit is set
• FERR bit is set
• RCREG = 00h
The second method uses the Auto-Wake-up feature
described in Section 18.3.3 “Auto-Wake-up on
Break”. By enabling this feature, the EUSART will
sample the next two transitions on RX/DT, cause an
RCIF interrupt, and receive the next data byte followed
by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Detect feature.
For both methods, the user can set the ABDEN bit of
the BAUDCON register before placing the EUSART in
Sleep mode.
RECEIVING A BREAK CHARACTER
bit 11
Auto Cleared
 2010 Microchip Technology Inc.
Stop bit