PIC18F86J90T-I/PT Microchip Technology, PIC18F86J90T-I/PT Datasheet - Page 328

• Manufacturer Part Number: PIC18F86J90T-I/PT
• Description: Segmented LCD, 96KB Flash, 4KB RAM, 12 MIPS, NanoWatt 80 TQFP 12x12x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F86J90T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3923 B
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 67
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F87J90 FAMILY
REGISTER 25-3:
DS39933D-page 328
bit 7
Legend:
R = Readable bit
-n = Value when device is unprogrammed
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
R/WO-1
IESO
IESO: Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Two-Speed Start-up enabled
0 = Two-Speed Start-up disabled
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
Unimplemented: Read as ‘0’
LPT1OSC: T1OSC/SOSC Power Selection Configuration bit
1 = High-power T1OSC/SOSC circuit selected
0 = Low-power T1OSC/SOSC circuit selected
T1DIG: T1CKI for Digital Input Clock Enable bit
1 = T1CKI is available as a digital input without enabling T1OSCEN
0 = T1CKI is not available as a digital input without enabling T1OSCEN
FOSC<2:0>: Oscillator Selection bits
111 = ECPLL OSC1/OSC2 as primary; ECPLL oscillator with PLL enabled; CLKO on RA6
110 = EC OSC1/OSC2 as primary; external clock with F
101 = HSPLL OSC1/OSC2 as primary; high-speed crystal/resonator with software PLL control
100 = HS OSC1/OSC2 as primary; high-speed crystal/resonator
011 = INTPLL1 internal oscillator block with software PLL control; F
010 = INTIO1 internal oscillator block with F
001 = INTPLL2 internal oscillator block with software PLL control and I/O on RA6 and RA7
000 = INTIO2 internal oscillator block with I/O on RA6 and RA7
R/WO-1
FCMEN
CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h)
WO = Write-Once bit
U-0
—
LPT1OSC
R/WO-1
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
OSC
R/WO-1
T1DIG
/4 output on RA6 and I/O on RA7
OSC
/4 output
R/WO-1
FOSC2
OSC
 2010 Microchip Technology Inc.
/4 output
‘0’ = Bit is cleared
R/WO-1
FOSC1
R/WO-1
FOSC0
bit 0