XR16L570IL24-F Exar Corporation, XR16L570IL24-F Datasheet - Page 25

• Manufacturer Part Number: XR16L570IL24-F
• Description: 2.25 To 5.5V W/ 5V TOLERANT INPUT UART W/16 BYTE FIFO W/ POWER SAVE
• Manufacturer: Exar Corporation

Specifications of XR16L570IL24-F

• Features: *
• Number Of Channels: 1, UART
• Fifo's: 16 Byte
• Protocol: RS232, RS422
• Voltage - Supply: 1.62 V ~ 5.5 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 24-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REV. 1.0.1
]
ISR[0]: Interrupt Status
•
•
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
ISR[5:4]: Interrupt Status
These bits are enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data
match of the Xoff character(s). Note that once set to a logic 1, the ISR bit-4 will stay a logic 1 until a Xon
character is received. ISR bit-5 indicates that CTS# or RTS# has changed state.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
•
•
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
•
•
4.6
P
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition) or wake-up interrupt. The wake-up interrupt is issued when
the L570 has been awakened from sleep mode.
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
L
RIORITY
EVEL
1
2
3
4
5
6
7
-
FIFO Control Register (FCR) - Write-Only
B
IT
0
0
0
0
0
0
1
0
-5
B
IT
0
0
0
0
0
1
0
0
-4
ISR R
B
EGISTER
IT
T
0
1
0
0
0
0
0
0
ABLE
-3
B
7: I
S
IT
TATUS
1
1
1
0
0
0
0
0
SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
-2
NTERRUPT
B
B
ITS
IT
1
0
0
1
0
0
0
0
-1
S
OURCE AND
25
B
IT
0
0
0
0
0
0
0
1
-0
LSR (Receiver Line Status Register)
RXRDY (Receive Data Time-out)
RXRDY (Received Data Ready)
TXRDY (Transmit Ready)
MSR (Modem Status Register)
RXRDY (Received Xoff or Special character)
CTS#, RTS# change of state
None (default) or Wake-up Interrupt
P
RIORITY
L
EVEL
S
OURCE OF INTERRUPT
XR16L570
Table
7).