DSP56303AG100 Freescale Semiconductor, DSP56303AG100 Datasheet - Page 88
![IC DSP 24BIT 100MHZ 144-LQFP](/photos/6/71/67148/dsp56303ag100_sml.jpg)
DSP56303AG100
Manufacturer Part Number
DSP56303AG100
Description
IC DSP 24BIT 100MHZ 144-LQFP
Manufacturer
Freescale Semiconductor
Series
DSP563xxr
Type
Fixed Pointr
Datasheet
1.DSP56303AG100.pdf
(108 pages)
Specifications of DSP56303AG100
Interface
Host Interface, SSI, SCI
Clock Rate
100MHz
Non-volatile Memory
ROM (576 B)
On-chip Ram
24kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
-40°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
144-LQFP
Package
144LQFP
Maximum Speed
100 MHz
Ram Size
24 KB
Device Million Instructions Per Second
100 MIPS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSP56303AG100
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100B1
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
DSP56303AG100R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Design Considerations
One way to evaluate power consumption is to use a current-per-MIPS measurement methodology to minimize
specific board effects (that is, to compensate for measured board current not caused by the DSP). A benchmark
power consumption test algorithm is listed in Appendix A. Use the test algorithm, specific test current
measurements, and the following equation to derive the current-per-MIPS value.
Where:
Note: F1 should be significantly less than F2. For example, F2 could be 66 MHz and F1 could be 33 MHz. The
4.4 PLL Performance Issues
The following explanations should be considered as general observations on expected PLL behavior. There is no
test that replicates these exact numbers. These observations were measured on a limited number of parts and were
not verified over the entire temperature and voltage ranges.
4.4.1
The phase skew of the PLL is defined as the time difference between the falling edges of
given capacitive load on
2, External Clock Timing, on page 2-5 for input frequencies greater than 15 MHz and the MF ≤4, this skew is
greater than or equal to 0.0 ns and less than 1.8 ns; otherwise, this skew is not guaranteed. However, for MF < 10
and input frequencies greater than 10 MHz, this skew is between − 1.4 ns and +3.2 ns.
4.4.2
The phase jitter of the PLL is defined as the variations in the skew between the falling edges of
for a given device in specific temperature, voltage, input frequency, MF, and capacitive load on
variations are a result of the PLL locking mechanism. For input frequencies greater than 15 MHz and MF ≤ 4, this
jitter is less than ±0.6 ns; otherwise, this jitter is not guaranteed. However, for MF < 10 and input frequencies
greater than 10 MHz, this jitter is less than ±2 ns.
4.4.3
The frequency jitter of the PLL is defined as the variation of the frequency of
this jitter is smaller than 0.5 percent. For mid-range MF (10 < MF < 500) this jitter is between 0.5 percent and
approximately 2 percent. For large MF (MF > 500), the frequency jitter is 2–3 percent.
4-4
6.
7.
degree of difference between F1 and F2 determines the amount of precision with which the current rating
can be determined for an application.
Equation 5:
Disable unused peripherals.
Disable unused pin activity (for example,
Phase Skew Performance
Phase Jitter Performance
Frequency Jitter Performance
I
I
F2
F1
CLKOUT
I
typF2
typF1
⁄
MIPS
=
=
=
=
, over the entire process, temperature and voltage ranges. As defined in Figure 2-
=
I
⁄
current at F2
current at F1
high frequency (any specified operating frequency)
low frequency (any specified operating frequency lower than F2)
MHz
DSP56303 Technical Data, Rev. 11
=
(
I
typF2
–
CLKOUT
I
typF1
)
⁄
,
(
F2 F1
XTAL
–
).
)
CLKOUT
. For small MF (MF < 10)
EXTAL
Freescale Semiconductor
EXTAL
CLKOUT
and
CLKOUT
and
. These
CLKOUT
for a