E-STE100P STMicroelectronics, E-STE100P Datasheet - Page 10

• Manufacturer Part Number: E-STE100P
• Description: IC TRANSCEIVER 3.3V 64 TQFP
• Manufacturer: STMicroelectronics
• Type: Transceiverr

Specifications of E-STE100P

• Number Of Drivers/receivers: 1/1
• Protocol: MII
• Voltage - Supply: 3.15 V ~ 3.45 V
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Number Of Receivers: 1
• Data Rate: 10/100Mbps
• Operating Supply Voltage (typ): 3.3V
• Package Type: TQFP
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.45V
• Operating Supply Voltage (min): 3.15V
• Mounting: Surface Mount
• Pin Count: 64
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2143; STE100P

STE100P
Table 5. Register Descriptions (continued)
10/31
LL* = Latching Low and clear by read. LH* = Latching High and clear by read.
PR2- PID1, PHY Identifier 1
PR3- PID2, PHY Identifier 2
PR4- ANA, Auto-Negotiation Advertisement
15~10
15~0
Bit #
9~4
3~0
15
14
6
5
4
3
2
1
0
PHYID1
PHYID2
MODEL
NXTPG
Name
MFPS
LINK
ANC
REV
EXT
JAB
AN
RF
---
MF Preamble Suppression
1 =Accepts management frames with pre-amble suppressed.
0 = Will not accept management frames with preamble
suppressed. The value of this bit is controlled by bit 1 of PR20.
Its default of 1 indicates that the SFEPHY1 accepts
management frame without preamble. A minimum of 32
preamble bits are required following power-on or hardware
reset. One IDLE bit is required between any two management
transactions as per IEEE 802.3u specification.
Auto-Negotiation Completed.
0: Auto-Negotiation process is not completed.
1: Auto-Negotiation process is completed. (PR0, Bit 12 is set)
Result of remote fault detection.
0: No remote fault condition detected.
1: Remote fault condition detected.
This bit is set when the Link Partner transmits a remote fault
condition (PR5 bit 13 = 1).
Auto-Negotiation ability.
Always 1, since STE100P has the Auto-Negotiation ability.
Link status.
0: a failure link condition occurred. (Latched until read)
1: a valid link is established.
Jabber detection.
1: jabber condition is detected (10Base-T only).
Extended register supporting.
Always 1, since STE100P supports extended register
Part one of PHY Identifier.
Assigned to the 3
Identifier (OUI). (The ST OUI is 0080E1 hex).
Part two of PHY Identifier.
Assigned to the 19
Identifier (OUI).
Model number of STE100P.
Six bits manufacture’s model number.
Revision number of STE100P.
Four bits manufacture’s revision number.
Next Page ability.
Always 0: since STE100P does not provide next page ability.
Reserved
rd
th
to 18
to 24
Descriptions
th
th
bits of the Organizationally Unique
bits of the Organizationally Unique
Default Val
000000b
000001b
1C04h
0001b
1
0
0
1
0
0
1
0
RW Type
RO/LH*
RO/LH*
RO/LL*
RO
RO
RO
RO
RO
RO
RO
RO
RO