E-STE100P STMicroelectronics, E-STE100P Datasheet - Page 13

• Manufacturer Part Number: E-STE100P
• Description: IC TRANSCEIVER 3.3V 64 TQFP
• Manufacturer: STMicroelectronics
• Type: Transceiverr

Specifications of E-STE100P

• Number Of Drivers/receivers: 1/1
• Protocol: MII
• Voltage - Supply: 3.15 V ~ 3.45 V
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Number Of Receivers: 1
• Data Rate: 10/100Mbps
• Operating Supply Voltage (typ): 3.3V
• Package Type: TQFP
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.45V
• Operating Supply Voltage (min): 3.15V
• Mounting: Surface Mount
• Pin Count: 64
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2143; STE100P

Table 5. Register Descriptions (continued)
LH = High Latching and cleared by reading.
PR18- XIE, XCVR Interrupt Enable Register
PR19- 100CTR, 100Base-TX Control Register
15,14
15~7
Bit #
13
12
3
2
1
0
6
5
4
3
2
1
0
DISRER
Name
ANAR
ANPR
ANCE
ANAE
ANPE
PDFE
REFE
ANC
PDF
REF
RFE
LDE
---
---
Interrupt source of Auto-Negotiation Acknowledge Received.
0: there is no link code word received.
1: link code word is receive from link partner.
Interrupt source of Parallel Detection Fault.
0: there is no parallel detection fault.
1: parallel detection is fault.
Interrupt source of Auto-Negotiation Page Received.
0: there is no Auto-Negotiation page received.
1: auto-negotiation page is received.
Interrupt source of Receive Error full.
0: the receive error number is less than 64.
1: 64 error packets are received.
Reserved
Auto-Negotiation Completed interrupt Enable.
0: disable Auto-Negotiation completed interrupt.
1: enable Auto-Negotiation complete interrupt.
Remote Fault detected interrupt Enable.
0: disable remote fault detection interrupt.
1: enable remote fault detection interrupt.
Link Down interrupt Enable.
0: disable link fail interrupt.
1: enable link fail interrupt.
Auto-Negotiation Acknowledge interrupt Enable.
0: disable link partner acknowledge interrupt
1: enable link partner acknowledge interrupt.
Parallel Detection Fault interrupt Enable.
0: disable fault parallel detection interrupt.
1: enable fault parallel detection interrupt.
Auto-Negotiation Page Received interrupt Enable.
0: disable Auto-Negotiation page received interrupt.
1: enable Auto-Negotiation page received interrupt.
RX_ERR full interrupt Enable.
0: disable rx_err full interrupt.
1: enable more than 64 time rx_err interrupt,
reserved
Disable the RX_ERR counter.
0: the receive error counter - RX_ERR is enabled.
1: the receive error counter - RX_ERR is disabled.
Auto-Negotiation completed. This bit is the same as PR1:5.
0: the Auto-Negotiation process has not completed yet.
1: the Auto-Negotiation process has completed.
Descriptions
Default Val
0
0
0
0
0
0
0
0
0
0
0
0
0
STE100P
RW Type
RO/LH*
RO/LH*
RO/LH*
RO/LH*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RO
13/31