DSPIC30F3011-30I/PT Microchip Technology Inc., DSPIC30F3011-30I/PT Datasheet - Page 153

• Manufacturer Part Number: DSPIC30F3011-30I/PT
• Description: 16 BIT MCU/DSP 44LD 30MIPS 24 KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F3011-30I/PT

• A/d Inputs: 9-Channels, 10-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 30
• Interface: I2C/SPI/UART, USART
• Ios: 30
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 44-pin TQFP
• Programmable Memory: 24K Bytes
• Ram Size: 1K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

21.0
There are several features intended to maximize sys-
tem reliability, minimize cost through elimination of
external components, provide Power Saving Operating
modes and offer code protection:
• Oscillator Selection
• Reset
• Watchdog Timer (WDT)
• Power Saving modes (Sleep and Idle)
• Code Protection
• Unit ID Locations
• In-Circuit Serial Programming (ICSP)
dsPIC30F devices have a Watchdog Timer, which is
permanently enabled via the configuration bits, or can
be software controlled. It runs off its own RC oscillator
for added reliability. There are two timers that offer nec-
essary delays on power-up. One is the Oscillator Start-
up Timer (OST), intended to keep the chip in Reset until
the crystal oscillator is stable. The other is the Power-
up Timer (PWRT), which provides a delay on power-up
only, designed to keep the part in Reset while the
power supply stabilizes. With these two timers on-chip,
most applications need no external Reset circuitry.
Sleep mode is designed to offer a very low current
Power-down mode. The user can wake-up from Sleep
through external Reset, Watchdog Timer Wake-up or
through an interrupt. Several oscillator options are also
made available to allow the part to fit a wide variety of
applications. In the Idle mode, the clock sources are
still active, but the CPU is shut-off. The RC oscillator
option saves system cost, while the LP crystal option
saves power.
 2004 Microchip Technology Inc.
Note: This data sheet summarizes features of this group
of dsPIC30F devices and is not intended to be a complete
reference source. For more information on the CPU,
peripherals, register descriptions and general device
functionality, refer to the dsPIC30F Family Reference
Manual (DS70046). For more information on the device
instruction set and programming, refer to the dsPIC30F
Programmer’s Reference Manual (DS70030).
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Programmable Brown-out Reset (BOR)
SYSTEM INTEGRATION
Preliminary
21.1
The dsPIC30F oscillator system has the following
modules and features:
• Various external and internal oscillator options as
• An on-chip PLL to boost internal operating
• A clock switching mechanism between various
• Programmable clock postscaler for system power
• A Fail-Safe Clock Monitor (FSCM) that detects
• Clock Control Register OSCCON
• Configuration bits for main oscillator selection
Table 21-1 provides a summary of the dsPIC30F
Oscillator Operating modes. A simplified diagram of the
oscillator system is shown in Figure 21-1.
Configuration bits determine the clock source upon
Power-on Reset (POR) and Brown-out Reset (BOR).
Thereafter, the clock source can be changed between
permissible clock sources. The OSCCON register
controls the clock switching and reflects system clock
related status bits.
clock sources
frequency
clock sources
savings
clock failure and takes fail-safe measures
Oscillator System Overview
dsPIC30F
DS70082G-page 151