PIC18F6520-I/PT Microchip Technology Inc., PIC18F6520-I/PT Datasheet - Page 160

• Manufacturer Part Number: PIC18F6520-I/PT
• Description: 64 PIN, 32 KB FLASH, 2048 RAM, 52 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F6520-I/PT

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 52
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 32K Bytes
• Ram Size: 2K Bytes
• Speed: 40 MHz
• Timers: 2-8 bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F6520/8520/6620/8620/6720/8720
17.3.1
The MSSP module has four registers for SPI mode
operation. These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer (SSPBUF)
• MSSP Shift Register (SSPSR) – Not directly
SSPCON1 and SSPSTAT are the control and status
registers in SPI mode operation. The SSPCON1 regis-
ter is readable and writable. The lower 6 bits of the
SSPSTAT are read-only. The upper two bits of the
SSPSTAT are read/write.
REGISTER 17-1:
DS39609B-page 158
accessible
REGISTERS
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SSPSTAT: MSSP STATUS REGISTER (SPI MODE)
bit 7
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode.
CKE: SPI Clock Select bit
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
D/A: Data/Address bit
Used in I
P: Stop bit
Used in I
SSPEN is cleared.
S: Start bit
Used in I
R/W: Read/Write bit information
Used in I
UA: Update Address bit
Used in I
BF: Buffer Full Status bit (Receive mode only)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Legend:
R = Readable bit
- n = Value at POR
R/W-0
Note:
SMP
2
2
2
2
2
C mode only.
C mode only. This bit is cleared when the MSSP module is disabled,
C mode only.
C mode only.
C mode only.
Polarity of clock state is set by the CKP bit (SSPCON1<4>).
R/W-0
CKE
W = Writable bit
‘1’ = Bit is set
D/A
R-0
R-0
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
P
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-0
S
R/W
R-0
 2004 Microchip Technology Inc.
x = Bit is unknown
R-0
UA
R-0
BF
bit 0