PIC18F26K80-I/SO Microchip Technology Inc., PIC18F26K80-I/SO Datasheet - Page 371

• Manufacturer Part Number: PIC18F26K80-I/SO
• Description: IC, MCU, nanoWatt; 8-bit w/ECAN; Flash, 64KB; 16MIPS; 8-ch, 12-BIT A/D; SOIC-28
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F26K80-I/SO

• A/d Inputs: 8-Channel, 12-Bit
• Comparators: 2
• Cpu Speed: 16 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 24
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SOIC
• Programmable Memory: 64K Bytes
• Ram Size: 3.6K Bytes
• Speed: 64 MHz
• Temperature Range: –40 to 125 °C
• Timers: 2-8-bit, 3-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part

After the A/D module has been configured as desired,
the selected channel must be acquired before the
conversion can start. The analog input channels must
have their corresponding TRIS bits selected as an
input. To determine acquisition time, see
“A/D Acquisition Requirements”
tion time has elapsed, the A/D conversion can be
started. An acquisition time can be programmed to
occur between setting the GO/DONE bit and the actual
start of the conversion.
To do an A/D conversion, follow these steps:
1.
FIGURE 23-5:
 2011 Microchip Technology Inc.
Configure the A/D module:
• Configure the required ADC pins as analog
• Set the voltage reference (ADCON1)
• Select the A/D positive and negative input
• Select the A/D acquisition time (ADCON2)
• Select the A/D conversion clock (ADCON2)
• Turn on the A/D module (ADCON0)
pins (ANCON0 and ANCON1)
channels (ADCON0 and ADCON1)
Legend: C
V
AIN
R
S
V
I
R
SS
C
R
LEAKAGE
T
PIN
IC
HOLD
SS
ANALOG INPUT MODEL
ANx
C
5 pF
PIN
= Input Capacitance
= Threshold Voltage
= Leakage Current at the pin due to
= Interconnect Resistance
= Sampling Switch
= Sample/Hold Capacitance (from DAC)
= Sampling Switch Resistance
various junctions
. After this acquisi-
Section 23.3
V
DD
V
V
T
T
= 0.6V
= 0.6V
Preliminary
PIC18F66K80 FAMILY
I
±100 nA
LEAKAGE
2.
3.
4.
5.
6.
7.
R
IC
Configure the A/D interrupt (if desired):
• Clear the ADIF bit (PIR1<6>)
• Set the ADIE bit (PIE1<6>)
• Set the GIE bit (INTCON<7>)
Wait the required acquisition time (if required).
Start the conversion:
• Set the GO/DONE bit (ADCON0<1>)
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
OR
• Waiting for the A/D interrupt
Read A/D Result registers (ADRESH:ADRESL)
and, if required, clear bit, ADIF.
For the next conversion, begin with step 1 or 2,
as required.
The A/D conversion time per bit is defined as T
Before the next acquisition starts, a minimum wait
of 2 T
 1k
AD
is required.
SS
Sampling
Switch
V
DD
R
SS
Sampling Switch
1
V
SS
C
2
HOLD
3
DS39977C-page 371
= 25 pF
(k)
4
AD
.