ICS1893Y-10LF IDT, Integrated Device Technology Inc, ICS1893Y-10LF Datasheet - Page 110

• Manufacturer Part Number: ICS1893Y-10LF
• Description: PHYCEIVER LOW PWR 3.3V 64-TQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: PHYceiver™r
• Type: PHY Transceiverr

Specifications of ICS1893Y-10LF

• Protocol: MII
• Voltage - Supply: 3.14 V ~ 3.47 V
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Other names: 1893Y-10LF; 800-1935-5; ICS1893Y-10LF

9.3.3 Configuration Pins
ICS1893 Rev C 6/6/00
Table 9-4
Table 9-4.
10/100SEL
10TCSR
100TCSR
ANSEL
DPXSEL
Name
ICS1893 Data Sheet - Release
Pin
lists the configuration pins.
Configuration Pins
Number
Pin
10
26
24
2
9
Input or
Input or
Input or
Output
Output
Output
Type
Input
Input
Pin
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
10Base-T / 100Base-TX Select.
The ‘ Pin Type’ for this pin depends on the setting for the HW/SW pin
(pin 23). When the HW/SW pin is set for:
10M Transmit Current Set Resistor.
100M Transmit Current Set Resistor.
Auto-Negotiation Select.
The ‘ Pin Type’ for this pin depends on the setting for the HW/SW pin
(pin 23). When the HW/SW pin is set for:
Half-Duplex / Full-Duplex Select.
The ‘ Pin Type’ for this pin depends on the setting for the HW/SW pin
(pin 23). When the HW/SW pin is set for:
•
•
•
•
•
•
•
•
•
•
Hardware mode, this pin acts as an input. In this case, when the
signal on this pin is logic:
– Low, this pin selects 10Base-T operations.
– High, this pin selects 100Base-TX operations.
Software mode, this pin acts as an output that indicates the current
status of this pin. In this case, when the signal on this pin is logic:
– Low, this pin indicates 10Base-T operations are selected.
– High, this pin indicates 100Base-TX operations are selected.
A resistor, connected between this pin and ground, is required to
establish the value of the transmit current used in 10Base-T mode.
The value and tolerance of this resistor is specified in
“ Recommended Component Values”
A resistor, connected between this pin and ground, is required to
establish the value of the transmit current used in 100Base-TX
mode.
The value and tolerance of this resistor is specified in
“ Recommended Component Values”
Hardware mode, this pin acts as an input. In this case, when the
signal on this pin is logic:
– Low, this pin does not select Auto-Negotiation operations.
– High, this pin selects Auto-Negotiation operations.
Software mode, this pin acts as an output that indicates the current
status of this pin. In this case, when the signal on this pin is logic:
– Low, this pin indicates that Auto-Negotiation is disabled.
– High, this pin indicates that Auto-Negotiation is enabled.
Hardware mode, this pin acts as an input. In this case, when the
signal on this pin is logic:
– Low, this pin selects half-duplex operations.
– High, this pin selects full-duplex operations.
Software mode, this pin acts as an output that indicates the current
status of this pin. In this case, when the signal on this pin is logic:
– Low, this pin indicates that it is set for half-duplex operations.
– High, this pin indicates that it is set for full-duplex operations.
110
Chapter 9 Pin Diagram, Listings, and Descriptions
Pin Description
.
.
Section 10.3,
Section 10.3,
June, 2000