LPC2194HBD64/01-S NXP Semiconductors, LPC2194HBD64/01-S Datasheet - Page 12

• Manufacturer Part Number: LPC2194HBD64/01-S
• Description: MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC 256KB Flash 1.8V/3.3V 64-Pin LQFP Tray
• Manufacturer: NXP Semiconductors

Specifications of LPC2194HBD64/01-S

• Package: 64LQFP
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 60 MHz
• Ram Size: 16 KB
• Program Memory Size: 256 KB
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 16|32 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 46
• Interface Type: CAN/I2C/SPI/SSP/UART
• On-chip Adc: 4-chx10-bit
• Operating Temperature: -40 to 125 °C
• Number Of Timers: 2

NXP Semiconductors
LPC2194_5
Product data sheet
6.5.1 Interrupt sources
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are requesting, the
VIC provides the address of the highest-priority requesting IRQs service routine,
otherwise it provides the address of a default routine that is shared by all the non-vectored
IRQs. The default routine can read another VIC register to see what IRQs are active.
Table 3
one interrupt line connected to the Vectored Interrupt Controller, but may have several
internal interrupt flags. Individual interrupt flags may also represent more than one
interrupt source.
Table 3.
Block
WDT
-
ARM Core
ARM Core
Timer 0
Timer 1
UART0
UART1
PWM0
I
SPI0
SPI1 and SSP
PLL
RTC
2
C-bus
lists the interrupt sources for each peripheral function. Each peripheral device has
Interrupt sources
[1]
Flag(s)
Watchdog Interrupt (WDINT)
Reserved for software interrupts only
EmbeddedICE, DbgCommRx
EmbeddedICE, DbgCommTx
Match 0 to 3 (MR0, MR1, MR2, MR3)
Capture 0 to 3 (CR0, CR1, CR2, CR3)
Match 0 to 3 (MR0, MR1, MR2, MR3)
Capture 0 to 3 (CR0, CR1, CR2, CR3)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Status Interrupt (MSI)
Match 0 to 3 (MR0, MR1, MR2, MR3, MR4, MR5, MR6)
SI (state change)
SPIF, MODF
SPIF, MODF and TXRIS, RXRIS, RTRIS, RORRIS
PLL Lock (PLOCK)
RTCCIF (Counter Increment), RTCALF (Alarm)
Rev. 05 — 10 December 2007
Single-chip 16/32-bit microcontroller
LPC2194
© NXP B.V. 2007. All rights reserved.
VIC channel #
0
1
2
3
4
5
6
7
8
9
10
11
12
13
12 of 40