AU5783D,512 NXP Semiconductors, AU5783D,512 Datasheet
AU5783D,512
Specifications of AU5783D,512
935263974512
AU5783D
Related parts for AU5783D,512
AU5783D,512 Summary of contents
Page 1
AU5783 J1850/VPW transceiver with supply control function Preliminary specification Supersedes data of 2000 Nov 29 hilips Semiconductors INTEGRATED CIRCUITS 2001 Feb 15 ...
Page 2
Philips Semiconductors J1850/VPW transceiver with supply control function FEATURES Supports SAE/J1850 VPW standard for in-vehicle class B multiplexing Bus speed 10.4 kbit/s nominal 4X transmission mode (41.6 kbit/s) Drive capability 32 bus nodes Low RFI due to output waveshape function ...
Page 3
Philips Semiconductors J1850/VPW transceiver with supply control function BLOCK DIAGRAM R NSTB 4X/LOOP Vcc (+5V) 1. Vbat INH LWAKE 2001 Feb 15 BATTERY (+12V) BAT VOLTAGE REFERENCE TX– BUFFER MODE CONTROL VOLTAGE REFERENCE WAKE-UP CONTROL GND ...
Page 4
Philips Semiconductors J1850/VPW transceiver with supply control function PINNING Pin configuration 1 R/F 2 GND 3 4X/LOOP 4 NSTB AU5783 N.C. 7 SO14 Figure 2. Pin configuration Pin description SYMBOL PIN DESCRIPTION R/F 1 Rise/fall time ...
Page 5
Philips Semiconductors J1850/VPW transceiver with supply control function standby mode if the POR is tripped. Even if the device is not in sleep mode the INH output will turn off at some battery voltages below 4.4 V when the internal ...
Page 6
Philips Semiconductors J1850/VPW transceiver with supply control function Table 1. Control input summary Z = Input connected to high impedance permitting it to float. Typically accomplished by turning off the output of a microcontroller Don’t care; The input ...
Page 7
Philips Semiconductors J1850/VPW transceiver with supply control function ABSOLUTE MAXIMUM RATINGS According to the IEC 134 Absolute Maximum System. Unless otherwise specified, operation is not guaranteed under these conditions: all voltages are referenced to pin GND; positive currents flow into ...
Page 8
Philips Semiconductors J1850/VPW transceiver with supply control function DC ELECTRICAL CHARACTERISTICS 7V < V < –40 C < T < +125 C; 250 BAT amb –2V < V < NSTB = 5 V; 4X/LOOP = 5 ...
Page 9
Philips Semiconductors J1850/VPW transceiver with supply control function SYMBOL PARAMETER Pin BUS V BUS output high voltage in normal mode BOh_n V BUS output high voltage in high speed BOh_h mode V BUS voltage; low battery BOhl –I BUS short ...
Page 10
Philips Semiconductors J1850/VPW transceiver with supply control function DYNAMIC CHARACTERISTICS 7 V < V < –40 C < T < +125 C; –2 V < V BAT amb BUS: 250 < R < 1 ...
Page 11
Philips Semiconductors J1850/VPW transceiver with supply control function TEST CIRCUITS TX NSTB S1 4X/LOOP S2 RX 3.9k NOTE: 1. Check I_LOG with the following switch positions open = open closed 3. ...
Page 12
Philips Semiconductors J1850/VPW transceiver with supply control function APPLICATION INFORMATION 100 100 nF SAE/J1850/VPW BUS LINE NOTES: 1. Value of R depends, e.g., on type of bus node. Example: secondary node R ld ...
Page 13
Philips Semiconductors J1850/VPW transceiver with supply control function SO14: plastic small outline package; 14 leads; body width 3.9 mm 2001 Feb 15 13 Preliminary specification AU5783 SOT108-1 ...
Page 14
Philips Semiconductors J1850/VPW transceiver with supply control function Data sheet status Data sheet Product Definition status status Objective Development This data sheet contains the design target or goal specifications for product development. specification Specification may change in any manner without ...