SFSA16GBQ1BR8TO-I-DT-216-STD Swissbit NA Inc, SFSA16GBQ1BR8TO-I-DT-216-STD Datasheet

Page 1

Swissbit AG Swissbit reserves the right to change products or specifications without notice. Industriestrasse 4-8 CH-9552 Bronschhofen Switzerland Product data sheet Industrial SATA SSD 2.5” X-200 Series SATA II - 3.0Gb UDMA6 / MDMA2 / PIO4 Standard and ...

Page 2

X-200 Series SATA Solid State Drive 2.5” 64GByte 1 Feature summary 2.5-inch SATA Solid State Drive (SSD) 100.2mm x 70.0mm x 9.0mm Replacement of a standard SATA-compliant Hard Disk Drive (HDD) 7+15 pin (SATA+power) SATA connector SATA ...

Page 3

Contents 1 FEATURE SUMMARY ................................................................................................................................................................... 2 2 CONTENTS .................................................................................................................................................................................. 3 3 ORDER INFORMATION ............................................................................................................................................................... 5 3 VAILABLE TANDARD PART NUMBERS 3.2 O OEM FFERED OPTIONS ........................................................................................................................................................ 5 4 PRODUCT SPECIFICATION ........................................................................................................................................................... 6 4.1 P HYSICAL DESCRIPTION .......................................................................................................................................................... ...

Page 4

S.M.A.R. ETURN TATUS ............................................................................................................................................... 35 7.3 S.M.A.R. NABLE ISABLE TTRIBUTE 7.4 S.M.A.R. AVE TTRIBUTE ALUES 7.5 S.M.A.R.T. E OFF-LINE I XECUTE 7.6 S.M.A.R.T. R EAD DATA ..................................................................................................................................................... 36 8 PACKAGE ...

Page 5

Order Information 3.1 Available Standard part numbers FIX / SATA II/ PIO4, MDMA2, UDMA6 / 0°C – 70°C Density Part Number 4GB SFSA4096QxBR4TO-C-MS-2y6-STD 8GB SFSA8192QxBR4TO-C-DT-2y6-STD 16GB SFSA16GBQxBR8TO-C-DT-2y6-STD 32GB SFSA32GBQxBR8TO-C-QT-2y6-STD 64GB SFSA64GBQxBR8TO-C-NC-2y6-STD Table 1: Commercial temperature product list x= depends ...

Page 6

Product Specification The Solid State Drive (SSD small form factor (2.5’’) non-volatile memory drive which provides high capacity data storage. It has a standard combined connector with SATA and power/control part. The card works at a supply ...

Page 7

Environmental Specifications 4.3.1 Recommended Operating Conditions Table 4: Recommended Operating Conditions Parameter Commercial Operating Temperature Industrial Operating Temperature Power Supply VCC Voltage Table 5: Current consumption (1) Current Consumption (type) Read (typ/max) Write (typ/max) Sleep/Idle Mode (typ/max) 1. All ...

Page 8

Electrical interface 5.1 Electrical description The SSD is connected with a standard 7 pin SATA connector and a standard 15 pin SATA power connector. The signal/pin assignments and descriptions are listed in Table 11 The signal/pin assignments and descriptions ...

Page 9

Electrical Specification Table 12 and Table 13 define the DC Characteristics of the SSD. Unless otherwise stated, conditions are: Vcc = 5.0V ± 10% 0°C to +70°C The current is measured by connecting an amp meter in series with ...

Page 10

ATA command description This section provides information on the ATA commands supported by the SSD. The commands are issued to the ATA by loading the required registers in the command block with the supplied parameter, and then writing the ...

Page 11

For reasons of backward compatibility some commands are implemented as ‘no operation’ NOP. Table 14 summarizes the Drive command set with the paragraphs that follow describing the individual commands and the task file for each. Table 14: ATA Command Set ...

Page 12

Check Power Mode (98h or E5h) This command checks the power mode. Issuing the command while the Drive is in Standby mode, is about to enter Standby exiting Standby, the command will set BSY, set the Sector ...

Page 13

Flush Cache (E7h) This command causes the drive to complete writing data from its cache. The drive returns status with RDY=1 and DSC=1 after the data in the write cache buffer is written to the media. If the drive ...

Page 14

Table 21: Identify Device Information Word Default Total Address Value Bytes 0 044Ah XXXXh 2 2 0000h 2 3 00XXh 2 4 0000h 2 5 XXXXh 2 6 XXXXh 2 7-8 XXXXh 4 9 0000h 2 10-19 aaaa ...

Page 15

Word 0: General Configuration This field indicates the general characteristics of the device. The default value for Word 0 is set to 045Ah. Some operating systems require Bit 6 of Word set to ‘1’ (Non-removable device) ...

Page 16

Word 54-56: Current Number of Cylinders, Heads, Sectors/Track These fields contain the current number of user addressable Cylinders, Heads, and Sectors/Track in the current translation mode. 6.5.14 Word 57-58: Current Capacity This field contains the product of the current ...

Page 17

If this field is supported, bit 1 of word 53 shall be set to one. The value in word 66 shall not be less than the value in word 65. This field shall be supported by all Drives supporting DMA ...

Page 18

Words 82-84: Features/command sets supported Words 82, 83, and 84 shall indicate features/command sets supported. The value 0000h or FFFFh was placed in each of these words by Drives prior to ATA-3 and shall be interpreted by the host ...

Page 19

If bit 2 of word 86 shall be set to zero, the Drive does not support the CFA feature set. If bit 3 of word 86 is set to one, the Advanced Power Management feature set has been enabled via ...

Page 20

Idle (97h or E3h) This command causes the Drive to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero interpreted as a timer count (each count is 5ms) ...

Page 21

Read Buffer (E4h) The Read Buffer command enables the host to read the current contents of the Drive’s sector buffer. This command has the same protocol as the Read Sector(s) command. Table 25 defines the Read Buffer command Byte ...

Page 22

Disk errors encountered during Read Multiple commands are posted at the beginning of the block or partial block transfer, but DRQ is still set and the data transfer will take place as it normally would, including transfer of corrupted data, ...

Page 23

Read Sector(s) (20h) This command reads from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When ...

Page 24

Table 32: Extended Error Codes Extended Error Code Description 00h No Error Detected 01h Self Test OK (No Error) 09h Miscellaneous Error 21h Invalid Address (Requested Head or Sector Invalid) 2Fh Address Overflow (Address Too Large) 35h, 36h Supply or ...

Page 25

Security Erase Unit (F4h) This command requests transfer of a single sector of data from the host. Table 34 defines the content of this sector of information. If the password does not match the password previously saved by the ...

Page 26

Security Set Password (F1h) This command requests a transfer of a single sector of data from the host. Table 39 defines the content of the sector of information. The data transferred controls the function of this command. Table 40 ...

Page 27

Security Unlock (F2h) This command requests transfer of a single sector of data from the host. Table 34 defines the content of this sector of information. If the identifier bit is set to Master and the device is in ...

Page 28

Features 02h and 82h allow the host to enable or disable write cache in SSD that implement write cache. When the subcommand disable write cache is issued, the SSD shall initiate the sequence to flush cache to non-volatile memory before ...

Page 29

Features 0Ah and 8Ah are used to enable and disable Power Level 1 commands. Feature 0Ah is the default feature for the SSD with extended power as they require Power Level 1 to perform their full set of functions. Power ...

Page 30

On save to disk 1. BIOS receives control prior to shut down; 2. BIOS issues a READ NATIVE MAX ADDRESS command to find the max capacity of the device; 3. BIOS issues a volatile SET MAX ADDRESS command to the ...

Page 31

S.M.A.R.T. (B0h) The intent of self-monitoring, analysis, and reporting technology (the SMART feature set protect user data and minimize the likelihood of unscheduled system downtime that may be caused by predictable degradation and/or fault of the device. ...

Page 32

Translate Sector (87h) This command is effectively a NOP command and only implemented for backward compatibility. The Sector Count Register will always be returned with a ‘00h’ indicating Translate Sector is not needed. Table 53 defines the Translate Sector ...

Page 33

Write Multiple Command (C5h) This command is similar to the Write Sectors command. The Drive sets BSY within 400ns of accepting the command. Interrupts are not presented on each sector but on the transfer of a block which contains ...

Page 34

Write Sector(s) (30h) This command writes from 1 to 256 sectors as specified in the Sector Count Register. A sector count of zero requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When ...

Page 35

S.M.A.R.T. Functionality The SSD supports the following SMART commands, determined by the Feature Register value. Table 60: S.M.A.R.T. Features Supported Feature Operation D0h SMART Read Data D1h SMART Read Attribute Thresholds D2h SMART Enable/Disable Autosave D3h SMART Save Attribute ...

Page 36

S.M.A.R.T. Enable / Disable Attribute Autosave This command is effectively a no-operation as the data for the SMART functionality is always available and kept current in the SSD. Table 63: S.M.A.R.T. Enable / Disable Attribute Autosave (Feature D2h) Task ...

Page 37

The data structure returned is: Table 67: S.M.A.R.T. Data Structure Offset Typ. Value Description 0..1 0100h SMART structure version 2..361 30x12Bytes Attribute entries (12 bytes each, little endian, see below) 362 31h Off-line data collection status (no ...

Page 38

Attribute Entries This table shows the structure of the S.M.A.R.T. attribute entries in the S.M.A.R.T. data structure. Table 69: Attribute Entry Offset Value Description 0 xxh Attribute ID – (see Table 68) 1..2 0000h Flags – Old age 3 ...

Page 39

Package mechanical Figure 1: SSD Drive Dimensions Dimension Height Width Max. Length Hole height 2. hole 3. hole Hole position Hole distance 2. hole 3. hole Screw head diameter Hole depth bottom A16 min Hole depth side A17 min ...

Page 40

Figure 2: Connector location Bottom side Top side Swissbit AG Swissbit reserves the right to change products or specifications without notice. Industriestrasse 4-8 CH-9552 Bronschhofen Switzerland www.swissbit.com industrial@swissbit.com Revision: 1.00 X-200_data_sheet_SA-QxBR_Rev100.doc Page ...

Page 41

Declaration of Conformity Product Type: Solid State Drive (SSD) Brand Name: SWISSMEMORY Model Designation: SFSAxxxxQxxxxxx-x-xx-xxx-xxx Manufacturer: Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland The product complies with the requirements of the following directives: CENELEC EN 55022B :2000 + CISPR22B ...

Page 42

RoHS and WEEE update from Swissbit Dear Valued Customer Swissbit place great value on the environment and thus pay close attention to the diverse aspects of manufacturing environmentally and health friendly products. The European Parliament and the ...

Page 43

Swissbit is obliged to minimize the hazardous substances in the products. According to part of the Directive, manufacturers are obliged to make a self-declaration for all devices with RoHS. Swissbit carried out intensive tests to comply with the self-declaration. We ...

Page 44

Part Number Decoder 64GB Manuf. Memory Type. Product Type Density Platform Product Generation Memory Organization 11.1 Manufacturer 11.2 Memory Type 11.3 Product Type 11.4 Density 11.5 Platform 11.6 Product Generation 11.7 Memory ...

Page 45

Temp. Option Industrial Temp. Range -40°C – 85°C Standard Temp. Range 11.12 DIE Classification SLC MONO (single die package) SLC DDP SLC QDP SLC ODP 11.13 PIN Mode Single nCE & R/nB Dual nCE & Dual R/nB Quad nCE ...

Page 46

Swissbit SSD Marking specification 12 12.1 Top view SFSA8192Q1BR4SA-I-QT-216-STD Assylot: 4500001235 Mfk Data 10/13 Made in Germany Industrial Drive 12.1.1 Label content: Swissbit logo o Density o CE logo o FCC logo o Pb-free logo o WEEE logo o Part ...

Page 47

Revision History Table 73: Document Revision History Date Revision Revision Details 29-September 1.00 initial release Disclaimer: No part of this document may be copied or reproduced in any form or by any means, or transferred to any third party, ...