SFSA16GBQ1BR8TO-I-DT-216-STD Swissbit NA Inc, SFSA16GBQ1BR8TO-I-DT-216-STD Datasheet - Page 28

• Manufacturer Part Number: SFSA16GBQ1BR8TO-I-DT-216-STD
• Description: FLASH SSD UDMA IND 2.5" 16GB
• Manufacturer: Swissbit NA Inc
• Series: X-200r

Specifications of SFSA16GBQ1BR8TO-I-DT-216-STD

• Memory Size: 16GB
• Memory Type: FLASH - NAND
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1052-1030

Features 02h and 82h allow the host to enable or disable write cache in SSD that implement write cache. When
the subcommand disable write cache is issued, the SSD shall initiate the sequence to flush cache to non-volatile
memory before command completion.
Feature 03h allows the host to select the PIO or Multiword DMA transfer mode by specifying a value in the Sector
Count register. The upper 5 bits define the type of transfer and the low order 3 bits encode the mode value. One
PIO mode shall be selected at all times. For Cards which support DMA, one DMA mode shall be selected at all
times. The host may change the selected modes by the Set Features command.
Table 44: Transfer Mode Values
Mode
PIO default mode
PIO default mode, disable IORDY
PIO flow control transfer mode
Reserved
Multi-Word DMA mode
Ultra DMA mode
Reserved
Notes: Multiword DMA is not permitted for devices configured in the PC Card Memory or the PC Card I/O interface
mode.
If a SSD supports PIO modes greater than 0 and receives a Set Features command with a Set Transfer Mode
parameter and a Sector Count register value of “00000000b”, it shall set its default PIO mode. If the value is
“00000001b” and the SSD supports disabling of IORDY, then the SSD shall set its default PIO mode and disable
IORDY. A SSD shall support all PIO modes below the highest mode supported, e.g., if PIO mode 1 is supported PIO
mode 0 shall be supported.
Support of IORDY is mandatory when PIO mode 3 or above is the current mode of operation.
A SSD reporting support for Multiword DMA modes shall support all Multiword DMA modes below the highest
mode supported. For example, if Multiword DMA mode 2 support is reported, then modes 1 and 0 shall also be
supported. Note that Multiword DMA shall not be supported while PC Card interface modes are selected.
A SSD reporting support for Ultra DMA modes shall support all Ultra DMA modes below the highest mode
supported. For example, if Ultra DMA mode 2 support is reported then modes 1 and 0 shall also be supported.
If an Ultra DMA mode is enabled, any previously enabled Multiword DMA mode shall be disabled by the device.
If a Multiword DMA mode is enabled any previously enabled Ultra DMA mode shall be disabled by the device.
Feature 05h allows the host to enable Advanced Power Management. To enable Advanced Power Management,
the host writes the Sector Count register with the desired advanced power management level and then executes
a Set Features command with subcommand code 05h. The power management level is a scale from the lowest
power consumption setting of 01h to the maximum performance level of Feh.
Table 45: Advanced power management levels shows these values.
Table 45: Advanced power management levels
In the current version the advanced power management levels are accepted, but don’t influence performance
and power consumption.
Device performance may increase with increasing power management levels. Device power consumption may
increase with increasing power management levels. The power management levels may contain discrete bands.
For example, a device may implement one power management method from 80h to A0h and a higher
performance, higher power consumption method from level A1h to Feh. Advanced power management levels
80h and higher do not permit the device to spin down to save power.
Feature 85h disables Advanced Power Management. Subcommand 85h may not be implemented on all devices
that implement Set Features subcommand 05h.
Swissbit AG
Industriestrasse 4-8
CH-9552 Bronschhofen
Switzerland
Level
Maximum performance
Intermediate power management levels without Standby
Minimum power consumption without Standby
Intermediate power management levels with Standby
Minimum power consumption with Standby
Reserved
Reserved
(1)Mode = transfer mode number
Swissbit reserves the right to change products or specifications without notice.
[e-mail]
www.swissbit.com
Bits (7:3)
00000b
00000b
00001b
00010b
00100b
01000b
1000b
X-200_data_sheet_SA-QxBR_Rev100.doc
Sector Count Value
81h-FDh
02h-7Fh
80h
00h
Feh
01h
FFh
Bits (2:0)
Mode
Mode
Mode
000b
001b
N/A
N/A
(1)
(1)
(1)
Revision: 1.00
Page 28 of 47