ACS8510 Semtech, ACS8510 Datasheet - Page 10

• Manufacturer Part Number: ACS8510
• Manufacturer: Semtech

Specifications of ACS8510

• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6/5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Package Type: LQFP
• Mounting: Surface Mount
• Pin Count: 100
• Lead Free Status / Rohs Status: Not Compliant

Local Oscillator Clock
Local Oscillator Clock
ITU and ETSI Specification
ITU and ETSI Specification
Telcordia GR-1244 CORE Specification
Telcordia GR-1244 CORE Specification
reference input and generate the T
the 8 kHz Frame Synchronization clock and the
2 kHz Multi-Frame Synchronization clock with
the same phase. The ACS8510 includes a
microprocessor port, providing access to the
configuration and status registers for device
setup and monitoring.
Local Oscillator Clock
Local Oscillator Clock
Local Oscillator Clock
The Master system clock on the ACS8510
should be provided by an external clock oscillator
of frequency 12.80 MHz. The clock specification
is important for meeting the ITU/ETSI and
Telcordia performance requirements for
Holdover mode. ITU and ETSI specifications
permit a combined drift characteristic, at
constant temperature, of all non-temperature-
related parameters, of up to 10 ppb per day.
The same specifications allow a drift of 1 ppm
over a temperature range of 0 to +70 °C.
Telcordia specifications are somewhat tighter,
requiring a non-temperature-related drift of less
than 40 ppb per day and a drift of 280 ppb
over the temperature range 0 to +50 °C.
ITU and ETSI Specification
ITU and ETSI Specification
ITU and ETSI Specification
Tolerance:
Drift*:
*Frequency drift over supply range of +2.7V to +3.3V.
Telcordia GR-1244 CORE Specification
Telcordia GR-1244 CORE Specification
Telcordia GR-1244 CORE Specification
Tolerance:
Drift*:
*Frequency drift over supply range of +2.7V to +3.3V.
Please contact Semtech for information on
crystal oscillator suppliers.
Revision 2.00/September 2003
ADVANCED COMMUNICATIONS
+/- 4.6 ppm over 20 year life time.
+/- 0.05 ppm/15 seconds @ constant temp.
+/- 0.01 ppm/day @ constant temp.
+/- 1 ppm over temp. range 0 to +70 °C
+/- 4.6 ppm over 20 year life time.
+/- 0.05 ppm/15 seconds @ constant temp.
+/- 0.04 ppm/day @ constant temp.
+/- 0.28 ppm over temp. range 0 to +50 °C
Semtech Corp.
OUT0
clock,
10
Crystal Frequency Calibration
Crystal Frequency Calibration
Crystal Frequency Calibration
Crystal Frequency Calibration
Crystal Frequency Calibration
The absolute crystal frequency accuracy is less
important than the stability since any frequency
offset can be compensated by adjustment of
register values in the IC. This allows for
calibration and compensation of any crystal
frequency variation away from its nominal value.
+/- 50 ppm adjustment would be sufficient to
cope with most crystals, in fact the range is an
order of magnitude larger due to the use of
two 8 bit register locations. The setting of the
conf_nominal_frequency register allows for this
adjustment. An increase in the register value
increases the output frequencies by 0.02 ppm
for each LSB step. The default value (in decimal)
is 39321. The minimum being 0 and the
maximum 65535, gives a -700 ppm to
+500 ppm adjustment range of the output
frequencies.
For example, if the crystal was oscillating at
12.8 MHz + 5 ppm, then the calibration value
in the register to give a -5 ppm adjustment in
output frequencies to compensate for the
crystal inaccuracy, would be :
Input Interfaces
Input Interfaces
Input Interfaces
Input Interfaces
Input Interfaces
The ACS8510 supports up to fourteen input
reference clock sources from input types T
T
AMI buffer I/O technologies. These interface
technologies support +3.3 V and +5 V
operation.
Over-Voltage Protection
Over-Voltage Protection
Over-Voltage Protection
Over-Voltage Protection
Over-Voltage Protection
The ACS8510 may require Over-Voltage
Protection on input reference clock ports
according to ITU Recommendation K.41.
Semtech protection devices are recommended
for this purpose (see separate Semtech data
book).
IN2
ACS8510 Rev2.1 SETS
39321 - (5 / 0.02) = 39071 (decimal)
and T
IN3
using TTL, CMOS, PECL, LVDS and
www.semtech.com
FINAL
IN1
,