ISP1761BE STEricsson, ISP1761BE Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/6/636/stericsson_sml.jpg)
ISP1761BE
Manufacturer Part Number
ISP1761BE
Description
Manufacturer
STEricsson
Datasheet
1.ISP1761BE.pdf
(164 pages)
Specifications of ISP1761BE
Operating Temperature (min)
-40C
Operating Temperature Classification
Industrial
Operating Temperature (max)
85C
Package Type
LQFP
Rad Hardened
No
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISP1761BE
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
ISP1761_5
Product data sheet
7.3.1 PIO mode access, memory read cycle
7.3.2 PIO mode access, memory write cycle
access must always be completed using two subsequent accesses. In the case of a DMA
transfer, the 16-bit or 32-bit data bus width configuration will determine the number of
bursts that will complete a certain transfer length.
In PIO mode, CS_N, WR_N and RD_N are used to access registers and memory. In DMA
mode, the data validation is performed by DACK, instead of CS_N, together with the
WR_N and RD_N signals. The DREQ signal will always be asserted as soon as the
ISP1761 DMA is enabled.
The following method is implemented to reduce the read access timing in a memory read:
The PIO memory write access is similar to a normal memory access. It is not necessary
to set the pre-fetching address before a write cycle to memory.
The ISP1761 internal write address will not automatically be incremented during
consecutive write accesses, unlike in a series of ISP1761 memory read cycles. The
memory write address must be incremented before every access.
•
•
•
The Memory register contains the starting address and the bank selection to read
from the memory. Before every new read cycle of the same or different banks, an
appropriate value is written to this register.
Once a value is written to this register, the address is stored in the FIFO of that bank
and is then used to pre-fetch data for the memory read of that bank.
For every subsequent read operation executed at a contiguous address, the address
pointer corresponding to that bank is automatically incremented to pre-fetch the next
data to be sent to the CPU.
Memory read accesses for multiple banks can be interleaved. In this case, the FIFO
block handles the multiplexing of appropriate data to the CPU.
The address written to the Memory register is incremented and used to successively
pre-fetch data from the memory irrespective of the value on the address bus for each
bank, until a new value for a bank is written to the Memory register. This is valid only
when the address refers to the memory space (400h to FFFFh).
For example, consider the following sequence of operations:
– Write the starting (read) address 4000h and bank1 = 01 to the Memory register.
– Write the starting (read) address 4100h and bank2 = 10 to the Memory register.
When RD_N is asserted for three cycles with A[17:16] = 01, the returned data
corresponds to addresses 4000h, 4004h and 4008h.
Remark: Once 4000h is written to the Memory register for bank1, the bank select
value determines the successive incremental addresses used to fetch data. That
is, the fetching of data is independent of the address on A[15:0] lines.
When RD_N is asserted for four cycles with A[17:16] = 10, the returned data
corresponds to addresses 4100h, 4104h, 4108h and 410Ch.
Consequently, the RD_N assertion with A[17:16] = 01 will return data from 400Ch
because the bank1 read stopped there in the previous cycle. Also, RD_N
assertions with A[17:16] = 10 will now return data from 4110h because the bank2
read stopped there in the previous cycle.
Rev. 05 — 13 March 2008
Hi-Speed USB OTG controller
© NXP B.V. 2008. All rights reserved.
ISP1761
20 of 163