P89LV51RD2BBC NXP Semiconductors, P89LV51RD2BBC Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P89LV51RD2BBC
Manufacturer Part Number
P89LV51RD2BBC
Description
MCU 8-Bit 89LV 80C51 CISC 64KB Flash 3.3V 44-Pin TQFP Tray
Manufacturer
NXP Semiconductors
Datasheet
1.P89LV51RD2BBC557.pdf
(76 pages)
Specifications of P89LV51RD2BBC
Package
44TQFP
Device Core
80C51
Family Name
89LV
Maximum Speed
40 MHz
Ram Size
1 KB
Program Memory Size
64 KB
Operating Supply Voltage
3.3 V
Data Bus Width
8 Bit
Program Memory Type
Flash
Number Of Programmable I/os
32
Interface Type
SPI/UART
Operating Temperature
0 to 70 °C
Number Of Timers
3
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89LV51RD2BBC
Manufacturer:
WCH
Quantity:
1 200
Company:
Part Number:
P89LV51RD2BBC,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
P89LV51RB2_RC2_RD2_5
Product data sheet
6.6.5 Framing error
6.6.6 More about UART mode 1
6.6.7 More about UART modes 2 and 3
Table 26.
Table 27.
Framing error (FE) is reported in the SCON.7 bit if SMOD0 (PCON.6) = 1. If SMOD0 = 0,
SCON.7 is the SM0 bit for the UART, it is recommended that SM0 is set up before SMOD0
is set to ‘1’.
Reception is initiated by a detected 1-to-0 transition at RXD. For this purpose RXD is
sampled at a rate of 16 times whatever baud rate has been established. When a transition
is detected, the divide-by-16 counter is immediately reset to align its rollovers with the
boundaries of the incoming bit times.
The 16 states of the counter divide each bit time into 16ths. At the 7th, 8th, and 9th
counter states of each bit time, the bit detector samples the value of RXD. The value
accepted is the value that was seen in at least 2 of the 3 samples. This is done for noise
rejection. If the value accepted during the first bit time is not 0, the receive circuits are
reset and the unit goes back to looking for another 1-to-0 transition. This is to provide
rejection of false start bits. If the start bit proves valid, it is shifted into the input shift
register, and reception of the rest of the frame will proceed.
The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the
following conditions are met at the time the final shift pulse is generated: (a) RI = 0, and
(b) either SM2 = 0, or the received stop bit = 1.
If either of these two conditions is not met, the received frame is irretrievably lost. If both
conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is
activated.
Reception is performed in the same manner as in mode 1.
Bit
2
1
0
SM0, SM1
0 0
0 1
1 0
1 1
SCON - Serial port control register (address 98H) bit descriptions
SCON - Serial port control register (address 98H) SM0/SM1 mode definitions
Symbol
RB8
TI
RI
Rev. 05 — 15 December 2009
Description
In modes 2 and 3, is the 9th data bit that was received. In mode 1, if
SM2 = 0, RB8 is the stop bit that was received. In mode 0, RB8 is
undefined.
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in
mode 0, or at the stop bit in the other modes, in any serial transmission.
Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in
mode 0, or approximately halfway through the stop bit time in all other
modes. (See SM2 for exceptions). Must be cleared by software.
UART mode
0: shift register
1: 8-bit UART
2: 9-bit UART
3: 9-bit UART
P89LV51RB2/RC2/RD2
8-bit microcontrollers with 80C51 core
Baud rate
CPU clock / 6
variable
CPU clock / 32 or CPU
clock / 16
variable
© NXP B.V. 2009. All rights reserved.
…continued
39 of 76