NUC130RE3CN Nuvoton Technology Corporation of America, NUC130RE3CN Datasheet - Page 200

no-image

NUC130RE3CN

Manufacturer Part Number
NUC130RE3CN
Description
IC MCU 32BIT 128KB FLASH 64LQFP
Manufacturer
Nuvoton Technology Corporation of America
Series
NuMicro™ NUC100r
Datasheets

Specifications of NUC130RE3CN

Core Processor
ARM Cortex-M0
Core Size
32-Bit
Speed
50MHz
Connectivity
CAN, EBI/EMI, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
Number Of I /o
49
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Eeprom Size
-
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-LQFP
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
NUC130RE3CN
Manufacturer:
NuvoTon
Quantity:
5 600
Part Number:
NUC130RE3CN
Manufacturer:
Nuvoton Technology Corporation of America
Quantity:
10 000
Part Number:
NUC130RE3CN
Manufacturer:
NUVOTON
Quantity:
20 000
Company:
Part Number:
NUC130RE3CN
Quantity:
62 605
5.6.4
5.6.4.1
5.6.4.2
The CPU interfaces to the I
(control register), I2CSTATUS (status register), I2CDAT (data register), I2CADDRn (address
registers, n=0~3), I2CADMn (address mask registers, n=0~3), I2CLK (clock rate register) and
I2CTOC (Time-out counter register). All bit 31~ bit 8 of these I
reserved. These bits do not have any functions and are all zero if read back.
When I
by I2CON and I
I2CSTATUS, the I
Interrupt bit EI (I2CON [7]) is set high at this time, the I
I2CSTATUS[7:3] stores the internal state code, the lowest 3 bits of I2CSTATUS are always zero
and the content keeps stable until SI is cleared by software. The base address is 4002_0000 and
4012_0000.
I
register are irrelevant when I
must be loaded with the chip’s own slave address. The I
I2CADDRn are matched with the received slave address.
The I
hardware will respond to General Call address (00H). Clear GC bit to disable general call
function.
When GC bit is set and the I
after Master send general call address to I
I
I2CADMn (n=0~3). When the bit in the address mask register is set to one, it means the received
corresponding address bit is don’t-care. If the bit is set to zero, that means the received
corresponding register bit should be exact the same as address register.
This register contains a byte of serial data to be transmitted or a byte which just has been
received. The CPU can read from or write to this 8-bit (I2CDAT [7:0]) directly while it is not in the
process of shifting a byte. when I
Data in I2CDAT [7:0] remains stable as long as SI bit is set. While data is being shifted out, data
on the bus is simultaneously being shifted in; I2CDAT [7:0] always contains the last data byte
present on the bus. Thus, in the event of arbitration lost, the transition from master transmitter to
slave receiver is made with the correct data in I2CDAT [7:0].
I2CDAT [7:0] and the acknowledge bit form a 9-bit shift register, the acknowledge bit is controlled
by the I
acknowledge bit into I2CDAT [7:0] on the rising edges of serial clock pulses on the SCL line.
When a byte has been shifted into I2CDAT [7:0], the serial data is available in I2CDAT [7:0], and
the acknowledge bit (ACK or NACK) is returned by the control logic during the ninth clock pulse.
Serial data is shifted out from I2CDAT [7:0] on the falling edges of SCL clock pulses, and is
shifted into I2CDAT [7:0] on the rising edges of SCL clock pulses.
2
2
C port is equipped with four slave address registers I2CADDRn (n=0~3). The contents of the
C bus controllers support multiple address recognition with four address mask registers
Protocol Registers
Address Registers (I2CADDR)
2
Data Register (I2CDAT)
C ports support the “General Call” function. If the GC bit (I2CADDRn [0]) is set the I
2
NuMicro™ NUC130/NUC140 Technical Reference Manual
C port is enabled by setting ENS1 (I2CON [6]) to high, the internal states will be controlled
2
C hardware and cannot be accessed by the CPU. Serial data is shifted through the
2
C logic hardware. Once a new status code is generated and stored in
2
C Interrupt Flag bit SI (I2CON [3]) will be set automatically. If the Enable
2
C port through the following thirteen special function registers: I2CON
2
2
C is in master mode. In the slave mode, the bit field I2CADDRn[7:1]
C is in Slave mode, it can receive the general call address by 00H
2
C is in a defined state and the serial interrupt flag (SI) is set.
2
C bus, then it will follow status of GC mode.
- 200 -
2
C interrupt will be generated. The bit field
Publication Release Date: June 14, 2011
2
C hardware will react if the contents of
2
C special function registers are
Revision V2.01
2
C port

Related parts for NUC130RE3CN