STM32F407IGT6 STMicroelectronics, STM32F407IGT6 Datasheet - Page 59

• Manufacturer Part Number: STM32F407IGT6
• Description: IC MCU 32BIT 1MB FLASH 176LQFP
• Manufacturer: STMicroelectronics

Specifications of STM32F407IGT6

• Core Processor: ARM Cortex-M4
• Core Size: 32-Bit
• Speed: 168MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 140
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 24x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Core: ARM Cortex M4
• Processor Series: STM32F4
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 168 MHz
• Data Ram Size: 192 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 140
• Number Of Timers: 10
• Operating Supply Voltage: 1.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Interface Type: CAN, I2C, I2S, SPI, UART
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-11604

STM32F405xx, STM32F407xx
Table 10.
1. TBD stands for “to be defined”.
2. If PDR_ON is set to V
3. When the ADC is used, refer to
4. If V
5. It is recommended to power V
6. If T
7. In low power dissipation state, T
Symbol
70 °C).
V
V
V
V
DDA
CAP1
CAP2
P
T
T
BAT
A
REF+
A
D
J
is lower, higher P
can be tolerated during power-up and power-down operation.
pin is present, it must respect the following condition: V
General operating conditions
Backup operating voltage
When the internal regulator is ON,
V
connect a stabilization capacitor.
When the internal regulator is OFF
(BYPASS_REG connected to V
V
from 1.2 V.
Power dissipation at T
suffix 6 or T
Ambient temperature for 6 suffix
version
Ambient temperature for 7 suffix
version
Junction temperature range
CAP_1
CAP_1
and V
and V
SS
D
, this value can be lowered to 1.7 V when the device operates in a reduced temperature range (0 to
values are allowed as long as T
A
Parameter
= 105 °C for suffix 7
CAP_2
CAP_2
DD
Table 64: ADC
A
and V
can be extended to this range as long as T
must be supplied
pins are used to
A
= 85 °C for
DDA
from the same source. A maximum difference of 300 mV between V
characteristics.
DD
Doc ID 022152 Rev 1
(6)
),
(1)
(continued)
J
LQFP64
LQFP100
LQFP144
LQFP176
UFBGA176
Maximum power dissipation
Low power dissipation
Maximum power dissipation
Low power dissipation
6 suffix version
7 suffix version
does not exceed T
DDA
-V
REF+
Conditions
< 1.2 V.
Jmax
J
does not exceed T
.
(7)
(7)
Electrical characteristics
Jmax
1.65
Min
–40
–40
–40
–40
–40
–40
1.1
.
-
-
-
-
-
Max
TBD
TBD
TBD
TBD
TBD
105
105
125
105
125
3.6
1.3
85
DD
and
59/154
Unit
mW
°C
°C
°C
V
V