STM32F407IGT6 STMicroelectronics, STM32F407IGT6 Datasheet - Page 76

• Manufacturer Part Number: STM32F407IGT6
• Description: IC MCU 32BIT 1MB FLASH 176LQFP
• Manufacturer: STMicroelectronics

Specifications of STM32F407IGT6

• Core Processor: ARM Cortex-M4
• Core Size: 32-Bit
• Speed: 168MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 140
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 24x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Core: ARM Cortex M4
• Processor Series: STM32F4
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 168 MHz
• Data Ram Size: 192 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 140
• Number Of Timers: 10
• Operating Supply Voltage: 1.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Interface Type: CAN, I2C, I2S, SPI, UART
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-11604

Electrical characteristics
Note:
Caution:
76/154
Table 28.
1. Based on characterization, not tested in production.
2. TBD stands for “to be defined”.
3. Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator
4. The oscillator selection can be optimized in terms of supply current using an high quality resonator with
5. t
For C
5 pF to 15 pF range selected to match the requirements of the crystal or resonator (see
Figure
specifies a load capacitance which is the series combination of C
Load capacitance C
C
between 2 pF and 7 pF.
To avoid exceeding the maximum value of C
to use a resonator with a load capacitance C
capacitance of 12.5 pF.
Example: if you choose a resonator with a load capacitance of C
then C
Figure 24. Typical application with a 32.768 kHz crystal
t
SU(LSE)
Symbol
stray
design guide for ST microcontrollers”.
small R
32.768 kHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary
significantly with the crystal manufacturer
C
SU(LSE)
R
g
I
(3)
2
m
F
L1
is the pin capacitance and board or trace PCB-related capacitance. Typically, it is
L1
Resonator with
integrated capacitors
24). C
(5)
and C
S
= C
is the startup time measured from the moment it is enabled (by software) to a stabilized
value for example MSIV-TIN32.768kHz. Refer to crystal manufacturer for more details
Feedback resistor
Recommended load capacitance
versus equivalent serial
resistance of the crystal (R
LSE driving current
Oscillator Transconductance
startup time
LSE oscillator characteristics (f
L2
L1
L2
= 8 pF.
and C
C L2
C L1
it is recommended to use high-quality external ceramic capacitors in the
L
Parameter
has the following formula: C
L2,
32.768 kH z
resonator
are usually the same size. The crystal manufacturer typically
Doc ID 022152 Rev 1
OSC32_OU T
OSC32_IN
S
)
(4)
V
R F
DD
L1
L
V
≤
= 3.3 V, V
DD
LSE
and C
Conditions
R
controlled
S
7 pF. Never use a resonator with a load
is stabilized
L
Bias
gain
= 30 kΩ
= 32.768 kHz)
= C
L2
L1
IN
(15 pF) it is strongly recommended
= V
x C
SS
STM32F405xx, STM32F407xx
L2
STM32F
/ (C
TBD
Min
L
L1
f LSE
(1)(2)
-
-
-
-
= 6 pF, and C
L1
and C
+ C
TBD
TBD
Typ
-
-
-
L2
L2
) + C
.
ai17531
TBD
TBD
Max
stray
stray
-
-
-
= 2 pF,
where
µA/V
Unit
MΩ
pF
µA
s