AT89C5131A-RDTIM Atmel, AT89C5131A-RDTIM Datasheet - Page 152
AT89C5131A-RDTIM
Manufacturer Part Number
AT89C5131A-RDTIM
Description
C5131A 32K FLASH USB VQFP64 IND, 5V
Manufacturer
Atmel
Datasheet
1.AT89C5131A-RDTIM.pdf
(176 pages)
- Current page: 152 of 176
- Download datasheet (3Mb)
WDT During Power-down
and Idle
150
AT89C5131
Table 108. WDTPRG Register
WDTPRG - Watchdog Timer Out Register (0A7h)
Reset value = XXXX X000
In Power-down mode the oscillator stops, which means the WDT also stops. While in
Power-down mode the user does not need to service the WDT. There are 2 methods of
exiting Power-down mode: by a hardware reset or via a level activated external interrupt
which is enabled prior to entering Power-down mode. When Power-down is exited with
hardware reset, servicing the WDT should occur as it normally should whenever the
AT89C5131 is reset. Exiting Power-down with an interrupt is significantly different. The
interrupt is held low long enough for the oscillator to stabilize. When the interrupt is
brought high, the interrupt is serviced. To prevent the WDT from resetting the device
while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high.
It is suggested that the WDT be reset during the interrupt service routine.
To ensure that the WDT does not overflow within a few states of exiting of power-down,
it is better to reset the WDT just before entering power-down.
In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the
AT89C5131 while in Idle mode, the user should always set up a timer that will periodi-
cally exit Idle, service the WDT, and re-enter Idle mode.
Number
Bit
7
6
5
4
3
2
1
0
7
-
Mnemonic
Bit
S2
S1
S0
-
-
-
-
-
6
-
Description
Reserved
The value read from this bit is undetermined. Do not try to set this bit.
WDT Time-out select bit 2
WDT Time-out select bit 1
WDT Time-out select bit 0
S2 S1 S0 Selected Time-out
0
0
0
0
1
1
1
1
16384x2^S machine cycles
0
0
1
1
0
0
1
1
5
-
0
1
0
1
0
1
0
1
16384x2^(214 - 1) machine cycles, 16.3 ms at FOSCA = 12 MHz
16384x2^(215 - 1) machine cycles, 32.7 ms at FOSCA = 12 MHz
16384x2^(216 - 1) machine cycles, 65.5 ms at FOSCA = 12 MHz
16384x2^(217 - 1) machine cycles, 131 ms at FOSCA = 12 MHz
16384x2^(218 - 1) machine cycles, 262 ms at FOSCA = 12 MHz
16384x2^(219 - 1) machine cycles, 542 ms at FOSCA = 12 MHz
16384x2^(220 - 1) machine cycles, 1.05 s at FOSCA = 12 MHz
16384x2^(221 - 1) machine cycles, 2.09 s at FOSCA = 12 MHz
4
-
3
-
S2
2
S1
1
4136C–USB–04/05
S0
0
Related parts for AT89C5131A-RDTIM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 52PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU 32KB 3-3.6V USB 48-VQFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU 8051 32K FLASH USB 28-SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU 8051 32K FLASH USB 64-VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU 8051 32K FLASH USB 28-SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU 8051 32K FLASH USB 52-PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 48QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 52PLCC
Manufacturer:
Atmel
Datasheet: