SC16C652BIBS,157 NXP Semiconductors, SC16C652BIBS,157 Datasheet - Page 20
![IC UART DUAL W/FIFO 32HVQFN](/photos/6/51/65170/568-32-hvqfn_sml.jpg)
SC16C652BIBS,157
Manufacturer Part Number
SC16C652BIBS,157
Description
IC UART DUAL W/FIFO 32HVQFN
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C652BIB48128.pdf
(43 pages)
Specifications of SC16C652BIBS,157
Features
2 Channels
Number Of Channels
2, DUART
Fifo's
32 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
32-VFQFN Exposed Pad
Transmitter And Receiver Fifo Counter
Yes
Data Rate
5Mbps
Operating Supply Voltage (max)
5.5V
Mounting
Surface Mount
Pin Count
32
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-2046
935276387157
SC16C652BIBS
935276387157
SC16C652BIBS
Philips Semiconductors
SC16C652B_4
Product data sheet
7.4 Interrupt Status Register (ISR)
The SC16C652B provides six levels of prioritized interrupts to minimize external software
interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status
bits. Performing a read cycle on the ISR will provide the user with the highest pending
interrupt level to be serviced. No other interrupts are acknowledged until the pending
interrupt is serviced. A lower level interrupt may be seen after servicing the higher level
interrupt and re-reading the interrupt status bits.
data values (bits 5:0) for the six prioritized interrupt levels and the interrupt sources
associated with each of these interrupt levels.
Table 14:
Table 15:
Priority
level
1
2
2
3
4
5
6
Bit
7:6
5:4
3:1
0
Symbol
ISR[7:6]
ISR[5:4]
ISR[3:1]
ISR[0]
ISR[5]
0
0
0
0
0
0
1
Interrupt source
Interrupt Status Register bits description
ISR[4]
0
0
0
0
0
1
0
Description
FIFOs enabled. These bits are set to a logic 0 when the FIFOs are not being
used in the 16C450 mode. They are set to a logic 1 when the FIFOs are
enabled in the SC16C652B mode.
INT priority bits 4:3. These bits are enabled when EFR[4] is set to a logic 1.
ISR[4] indicates that matching Xoff character(s) have been detected. ISR[5]
indicates that CTS, RTS have been generated. Note that once set to a
logic 1, the ISR[4] bit will stay a logic 1 until Xon character(s) are received.
INT priority bits 2:0. These bits indicate the source for a pending interrupt at
interrupt priority levels 1, 2, and 3 (see
INT status.
Rev. 04 — 1 September 2005
logic 0 or cleared = default condition
logic 0 or cleared = default condition
logic 0 or cleared = default condition
logic 0 = an interrupt is pending and the ISR contents may be used as a
pointer to the appropriate interrupt service routine
logic 1 = no interrupt pending (normal default condition)
ISR[3]
0
0
1
0
0
0
0
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
ISR[2]
1
1
1
0
0
0
0
ISR[1]
1
0
0
1
0
0
0
Table 14 “Interrupt source”
ISR[0]
0
0
0
0
0
0
0
Table
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Source of the interrupt
LSR (Receiver Line Status
Register)
RXRDY (Received Data Ready)
RXRDY (Receive Data time-out)
TXRDY (Transmitter Holding
Register Empty)
MSR (Modem Status Register)
RXRDY (Received Xoff signal)/
Special character
CTS, RTS change of state
14).
SC16C652B
shows the
20 of 43