SC16C852SVIET,115 NXP Semiconductors, SC16C852SVIET,115 Datasheet - Page 11
![IC UART DL 1.8V W/FIFO 36-TFBGA](/photos/6/98/69857/36-tfbga_sot912-1_pkg_sml.jpg)
SC16C852SVIET,115
Manufacturer Part Number
SC16C852SVIET,115
Description
IC UART DL 1.8V W/FIFO 36-TFBGA
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C852SVIET151.pdf
(48 pages)
Specifications of SC16C852SVIET,115
Features
Programmable
Number Of Channels
2, DUART
Fifo's
128 Byte
Protocol
RS485
Voltage - Supply
1.8V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
36-TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935286451115
SC16C852SVIET-G
SC16C852SVIET-G
SC16C852SVIET-G
SC16C852SVIET-G
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C852SVIET,115
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
SC16C852SV_1
Product data sheet
6.7 Special character detect
6.8 Interrupt priority and time-out interrupts
Under the above described flow control mechanisms, flow control characters are not
placed (stacked) in the receive FIFO. When using software flow control, the Xon/Xoff
characters cannot be used for data transfer.
In the event that the receive buffer is overfilling, the SC16C852SV automatically sends an
Xoff character (when enabled) via the serial TX output to the remote UART. The
SC16C852SV sends the Xoff1/Xoff2 characters as soon as the number of received data
in the receive FIFO passes the programmed trigger level. To clear this condition, the
SC16C852SV will transmit the programmed Xon1/Xon2 characters as soon as the
number of characters in the receive FIFO drops below the programmed trigger level.
A special character detect feature is provided to detect an 8-bit character when EFR[5] is
set. When an 8-bit character is detected, it will be placed on the user-accessible data
stack along with normal incoming RXA/RXB data. This condition is selected in conjunction
with EFR[3:0] (see
using this special mode by setting EFR[3:0] to all zeroes.
The SC16C852SV compares each incoming receive character with Xoff2 data. If a match
occurs, the received data will be transferred to the FIFO, and ISR[4] will be set to indicate
detection of a special character. Although
Xon-1, Xon-2, Xoff-1, Xoff-2 with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register bits LCR[1:0]
define the number of character bits, that is, either 5 bits, 6 bits, 7 bits or 8 bits. The word
length selected by LCR[1:0] also determine the number of bits that will be used for the
special character comparison. Bit 0 in the Xon-1, Xon-2, Xoff-1, Xoff-2 registers
corresponds with the LSB bit for the received character.
The interrupts are enabled by IER[7:0]. Care must be taken when handling these
interrupts. Following a reset, if Interrupt Enable Register (IER) bit 1 = 1, the SC16C852SV
will issue a Transmit Holding Register interrupt. This interrupt must be serviced prior to
continuing operations. The ISR indicates the current singular highest priority interrupt
only. A condition can exist where a higher priority interrupt masks the lower priority
interrupt(s) (see
priority interrupt(s) be reflected in the status register. Servicing the interrupt without
investigating further interrupt conditions can result in data errors.
Receive Data Ready and Receive Time Out have the same interrupt priority (when
enabled by IER[0]), and it is important to serve these interrupts correctly. The receiver
issues an interrupt after the number of characters have reached the programmed trigger
level. In this case, the SC16C852SV FIFO may hold more characters than the
programmed trigger level. Following the removal of a data byte, the user should re-check
LSR[0] to see if there are any additional characters. A Receive Time Out will not occur if
the receive FIFO is empty. The time-out counter is reset at the center of each stop bit
received or each time the Receive Holding Register (RHR) is read. The actual time-out
value is 4 character time, including data information length, start bit, parity bit, and the
size of stop bit, that is, 1 , 1.5 , or 2 bit times.
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
Table
Table
Rev. 01 — 23 September 2008
12). Only after servicing the higher pending interrupt will the lower
24). Note that software flow control should be turned off when
Table 7 “SC16C852SV internal registers”
SC16C852SV
© NXP B.V. 2008. All rights reserved.
shows
11 of 48