SC16C654IA68,529 NXP Semiconductors, SC16C654IA68,529 Datasheet - Page 9
![IC UART QUAD W/FIFO 68-PLCC](/photos/6/98/69865/68-plcc_sot188-3_pkg_sml.jpg)
SC16C654IA68,529
Manufacturer Part Number
SC16C654IA68,529
Description
IC UART QUAD W/FIFO 68-PLCC
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654DIB64151.pdf
(52 pages)
Specifications of SC16C654IA68,529
Number Of Channels
4, QUART
Fifo's
64 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
68-LCC (J-Lead)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-3282-5
935270051529
SC16C654IA68-S
935270051529
SC16C654IA68-S
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C654IA68,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
Table 2:
9397 750 11617
Product data
Symbol
INTA, INTB,
INTC, INTD
INTSEL
IOR
IOW
IRQ
NC
RESET,
RESET
RIA, RIB,
RIC, RID
Pin description
Pin
PLCC68 LQFP64
15, 21,
49, 55
65
52
18
15
21, 49,
52, 54,
55, 65
37
8, 28,
42, 62
6, 12,
37, 43
-
40
9
-
-
27
63, 19,
30, 50
…continued
Type
O
I
I
I
O
-
I
I
Description
Interrupt A, B, C, D (Active-HIGH). This function is associated with the
16 mode only. These pins provide individual channel interrupts INTA-INTD.
INTA-INTD are enabled when MCR[3] is set to a logic 1, interrupts are enabled
in the interrupt enable register (IER), and when an interrupt condition exists.
Interrupt conditions include: receiver errors, available receiver buffer data,
transmit buffer empty, or when a modem status flag is detected. When the
68 mode is selected, the functions of these pins are re-assigned. 68 mode
functions are described under their respective name/pin headings.
Interrupt Select (Active-HIGH, with internal pull-down). This function is
associated with the 16 mode only. When the 16 mode is selected, this pin can
be used in conjunction with MCR[3] to enable or disable the 3-State interrupts,
INTA-INTD, or override MCR[3] and force continuous interrupts. Interrupt
outputs are enabled continuously by making this pin a logic 1. Making this pin a
logic 0 allows MCR[3] to control the 3-State interrupt output. In this mode,
MCR[3] is set to a logic 1 to enable the 3-State outputs. This pin is disabled in
the 68 mode. Due to pin limitations on the 64-pin packages, this pin is not
available. To cover this limitation, the SC16C654DIB64 version operates in the
continuous interrupt enable mode by bonding this pin to V
SC16C654IB64 operates with MCR[3] control by bonding this pin to GND.
Input/Output Read strobe (Active-LOW). This function is associated with the
16 mode only. A logic 0 transition on this pin will load the contents of an internal
register defined by address bits A0-A2 onto the SC16C654/654D data bus
(D0-D7) for access by external CPU. This pin is disabled in the 68 mode.
Input/Output Write strobe (Active-LOW). This function is associated with the
16 mode only. A logic 0 transition on this pin will transfer the contents of the
data bus (D0-D7) from the external CPU to an internal register that is defined
by address bits A0-A2. When the 16 mode is selected (PLCC68), this pin
functions as R/W (see definition under R/W).
Interrupt Request or Interrupt ‘A’. This function is associated with the
68 mode only. In the 68 mode, interrupts from UART channels A-D are
wire-ORed internally to function as a single IRQ interrupt. This pin transitions to
a logic 0 (if enabled by the interrupt enable register) whenever a UART
channel(s) requires service. Individual channel interrupt status can be
determined by addressing each channel through its associated internal
register, using CS and A3-A4. In the 68 mode, and external pull-up resistor
must be connected between this pin and V
to INTA when operating in the 16 mode (see definition under INTA).
Not connected.
Reset. In the 16 mode, a logic 1 on this pin will reset the internal registers and
all the outputs. The UART transmitter output and the receiver input will be
disabled during reset time. (See
conditions”
functions similarly, bus as an inverted reset interface signal, RESET.
Ring Indicator (Active-LOW). These inputs are associated with individual
UART channels, A through D. A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt.
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Rev. 04 — 19 June 2003
for initialization details.) When 16/68 is a logic 0 (68 mode), this pin
Section 7.11 “SC16C654/654D external reset
SC16C654/654D
CC
. The function of this pin changes
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
CC
internally. The
9 of 52